The Firing Line Forums

Go Back   The Firing Line Forums > The North Corral > Black Powder and Cowboy Action Shooting

Reply
 
Thread Tools
Old April 14, 2013, 10:23 PM   #1
Captchee
Senior Member
 
Join Date: April 2, 2013
Posts: 312
need advice , converted 1851

Ok so im very new to this aspect of BP pistols so im in search of advice as to what to do .
Recently I converted a Uberti 1851 to 38 long colt . This is a kirts conversion.
Ok so my barrel swags at .370 . I been shooting Ultra max 158 gr RN
The accuracy is ???? Well about a 12 inch pattern at 25 yards , off hand . The bullets are tumbling and im getting real nice little rectangles in the target .

Im new to reloading cartridges and today I cast up some .376 heeled bullest from one of my old Dixie moulds .
I tried reloading the .357 long colt casings in my 38 special dies . Well it didn’t work to well . The casings all sized fine but when I went to seat the bullet it would stick in my setting dieand pull back out of the casing . I would then have to take the die apart and nock the bullet out , then reset the die
The bullet is a 125 gr, with a rather sharp point . It mic to .357 ant the base and then to .370 at the first band then .376 at the nose

So now my question . Is the die for a heeled 38 cal long colt larger then a 38 special ?

I see that Lee makes a set of dies for 38 long and short colt . Is this the difference IE the seating die and crimp die is larger .

Now the other option is
a) wad cutters “ I don’t like them :
B)Hollow based .357 bullet . Which would be great if I could find a reasonably price HB .357 mould that doesn’t cost in the range of having the barrel relined

Im wondering if it would be better to simply have the barrel lined to .357 .
If this is your opinion as to the best thing to do , who would you recommend and what type of cost would I be looking at .

Anny advice would be appreciated
Captchee is offline  
Old April 15, 2013, 04:32 PM   #2
Captchee
Senior Member
 
Join Date: April 2, 2013
Posts: 312
LMAO ok . no replies ,
However i figured out what i was doing wrong LOL
Captchee is offline  
Old April 15, 2013, 05:02 PM   #3
Jim Watson
Senior Member
 
Join Date: October 25, 2001
Location: Alabama
Posts: 11,074
Well, good. What was it?

Me?
I had mine lined down to .358" so I would not have to play happy heel games.
(Hollowbase wadcutters worked most but not all the time.)
Jim Watson is offline  
Old April 15, 2013, 06:30 PM   #4
Captchee
Senior Member
 
Join Date: April 2, 2013
Posts: 312
well i have some 38LC brass and some 38 special brass .
i been trying to reload my 38LC
my dies are 38 special . so my exspander die wasnt exspanding the casing mouth like it should have been . as such it was compressing lead into the die and jamming it up .
but when i put 38 special casing in , it works fine .

this weekend i also picked up a old steel ,dixie heeled bullet mould that casts a 125 grain . which so happens is . 357 at the base ..367 at the first lub ring , then grows to .372 .
being im using soft lead , i rana lubed bullet through my .358 sizing die and WAAA LAAAA no more problems .

now im to figure out a way to hollow base the mould . after using a counter sink on the base , i still am getting a 110 grain bullet

but that was all after spending the morning shooting .60 rb from my 38 special casings . my group went from 12 inchs at 25 yards down to 6 inchs at 25 yards .
what a kick in the but .
Captchee is offline  
Old April 16, 2013, 04:39 AM   #5
newfrontier45
Junior member
 
Join Date: February 23, 2012
Posts: 921
I would have to have the barrel relined rather than screwing around with heeled bullets. However, there is a source for dies, bullets and info.

http://www.cartridgeconversion.com
newfrontier45 is offline  
Old April 16, 2013, 05:12 AM   #6
Hawg
Senior Member
 
Join Date: September 8, 2007
Location: Mississippi
Posts: 11,718
Having the barrel lined would be the best option.
Hawg is offline  
Old April 16, 2013, 06:14 AM   #7
Captchee
Senior Member
 
Join Date: April 2, 2013
Posts: 312
thanks for the imput guys .
finding a mould isnt an issue as i can make my own .
the problem was with the dies . actualy not even the dies , it was with me

as to re lining the barrel . ya im thinking ill probably end up doing that down the road . but with the groups i got yesterday , thats about as good as i can shoot a pistol now days anyway LOL
Captchee is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 03:43 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.07040 seconds with 9 queries