The Firing Line Forums

Go Back   The Firing Line Forums > The Hide > The Art of the Rifle: Semi-automatics

Thread Tools
Old April 12, 2013, 07:44 PM   #1
Senior Member
Join Date: December 5, 2012
Location: Lexington, NC
Posts: 102
Bent Marlin 60 Recoil Spring

Has anyone "un-bent" one sucessfully?

Anyone know where to get one without paying $7 S/H?
Jimboh247 is offline  
Old April 12, 2013, 10:47 PM   #2
Senior Member
Join Date: October 18, 2006
Posts: 6,146
I could go into a post about metalurgy and how once a spring is kinked it can't be unkinked, but based on my experience with a Marlin 60 with a bent main spring.....

Pay the 7 dollars S&H. My father, machinist for longer than I have been alive, had the same bent spring problem. He paid the 7 dollars S&H and considered it a bargain.

A bent recoil spring in a Marlin 60 will cause failures to cycle like nobodies business.

"Gorsh" said Goofy as secondary explosions racked the beaten zone, "Did I do that?"
Jimro is offline  
Old April 13, 2013, 05:20 AM   #3
Senior Member
Join Date: January 18, 2006
Location: Bowling Green,KY
Posts: 390
I bent one in my 60ss. I straightened it out because I wanted to shoot that day. I bought a new one but have not put it in yet. That was several thousand rounds ago.
Bowling Green, KY
Z400ACDC is offline  
Old April 13, 2013, 08:44 AM   #4
Junior Member
Join Date: January 14, 2013
Posts: 11
Re: Bent Marlin 60 Recoil Spring

Nope... I just waited until I needed a bunch of stuff from midway... Their shipping is only like $4... Might as well replace a bunch of springs and the buffer if it is older...
J_Grimm is offline  
Old April 14, 2013, 07:40 PM   #5
Senior Member
Join Date: November 11, 2006
Posts: 2,021
Sounds like the recoil assembly...

was inserted into the breech bolt reversed and bent the spring.
Get a new spring, may need to call some shop but one will have it, and reassemble correctly.

You could try and re-straighted the spring but need to re-temper.
jrothWA is offline  
Old April 14, 2013, 10:30 PM   #6
James K
Join Date: March 17, 1999
Posts: 21,803
Those springs can be cold straightened, but it requires a lot of patience and some experience. It is probably better to pay the tab, and buy a buffer or two at the same time.

Jim K
James K is offline  
Old April 15, 2013, 10:21 AM   #7
Senior Member
Join Date: September 28, 2008
Posts: 6,802
The kink will always cause trouble.
If you don't have a new spring, you can get by with cutting the kink out and just using the two halves of the spring as one.
It works pretty good and much easier to reinstall.
Lock the doors, they're coming in the windows.
g.willikers is offline  
Old April 15, 2013, 08:22 PM   #8
Senior Member
Join Date: December 5, 2012
Location: Lexington, NC
Posts: 102
I went ahead and ordered one from Midway. I might try the 2 piece spring deal when I get the replacement.
Jimboh247 is offline  

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

All times are GMT -5. The time now is 11:58 AM.

Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2015, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2015 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent:
Contact Us
Page generated in 0.07046 seconds with 9 queries