The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > Handloading, Reloading, and Bullet Casting

Reply
 
Thread Tools
Old April 9, 2013, 07:03 AM   #1
Jevyod
Member
 
Join Date: May 5, 2012
Location: Pennsylvania
Posts: 99
Misfires?

I loaded up some loads for my 8mm Mauser ( 1918 K98) About half of them did not fire the first time. After two or three tries, they did eventually fire. What is the likely culprit? Would it be the primers? I was using CCI 200.
Jevyod is offline  
Old April 9, 2013, 07:30 AM   #2
steve4102
Senior Member
 
Join Date: December 23, 2005
Location: Minnesota
Posts: 2,209
Nine times out of nine this is caused by a high primer, one that has not been seated fully to bottom out in the primer pocket. The first attempt the firing pin seats the primer deeper, the second attempt sets it off.
steve4102 is offline  
Old April 9, 2013, 07:36 AM   #3
William T. Watts
Senior Member
 
Join Date: January 20, 2010
Location: Central Arkansas
Posts: 774
Firing pin/firing pin spring, CCI has the hardest cup, Federal primers the softest. I think the primary cause is your firing pin spring, check your firing pin too it may have been damage in the past and someone cleaned up the tip. You might try Federal LP (if you can find them) and fix your failure to fire problem if the spring is weak.. William.
William T. Watts is offline  
Old April 9, 2013, 07:53 AM   #4
mehavey
Senior Member
 
Join Date: June 17, 2010
Location: Virginia
Posts: 2,879
If commercial and/or milsurp ammunition fires reliably, and you have double-checked that the
primers in reloads are bottomed out firmly, consider also "the possibility" that you might be
oversizing the case relative to the chamber.**

If you are fully sizing (down to shell-holder and then some), can you put succesive pieces
of scotch tape on the base of case and still close the bolt?




** I realize that the extractor "should" hold the case close enough to the bolt face to prevent
movement, but if there's a little extra clearance........

Last edited by mehavey; April 9, 2013 at 09:44 AM.
mehavey is offline  
Old April 9, 2013, 08:01 PM   #5
Slamfire
Senior Member
 
Join Date: May 27, 2007
Posts: 4,105
Have you taken the firing pin out of the bolt and cleaned out all the grease and gunk out from the insides of the bolt?

Then, have you installed a new mainspring? I can guarantee that after 60 to 70 years of compression, that mainspring has taken a set.

I buy the lowest pound (I think 20 lb) Mauser spring that Wolff makes and install them in my Mausers. It makes a difference.
__________________
If I'm not shooting, I'm reloading.
Slamfire is offline  
Old April 9, 2013, 10:20 PM   #6
LarryFlew
Senior Member
 
Join Date: June 15, 2009
Location: Minnesota CZ fan
Posts: 895
plus 1 for primers not seated all the way in. The extra hits are pushing the primer to the seat and then they do fire.
LarryFlew is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 06:04 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.07565 seconds with 9 queries