The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > Handloading, Reloading, and Bullet Casting

Reply
 
Thread Tools
Old March 23, 2013, 09:46 AM   #1
RockingReloading
Junior Member
 
Join Date: March 14, 2013
Posts: 4
Ar15 .223remington rounds

Iam setup to reload ar15 remington rounds i was checking to see if the bullets fit the casings good and the bullets (Nosler .224 35gr ) will not fit the casings tight enough to be crimped. What can i do ? what could i do to use these bullets to load the round?
RockingReloading is offline  
Old March 23, 2013, 01:31 PM   #2
steelman762
Member
 
Join Date: January 18, 2010
Posts: 61
You have put the casings through the full length resizing die first I assume?You are sure the bullets are .224? You should not crimp them if there is no canalure cut in them. That is a light bullet for the AR unless you have a slow twist rate. A fast twist is 7:1 and a slow is 12:1. Should be stamp on your AR. I have a 8:1 and don't use bullets much lighter than 55gr. Light bullets and a fast rate kind a fly apart or you loose accuracy.
steelman762 is offline  
Old March 23, 2013, 08:50 PM   #3
RockingReloading
Junior Member
 
Join Date: March 14, 2013
Posts: 4
AR15 .223 Rounds

yes i am positive that they are .224
RockingReloading is offline  
Old March 24, 2013, 01:51 AM   #4
higgite
Senior Member
 
Join Date: October 21, 2010
Posts: 266
What, if anything, have you done to the cases that you're trying to fit the bullets into? Are the cases new, fired, unknown? Have you full length sized them? Neck sized them? Not sized them at all? We need more info.
higgite is offline  
Old March 24, 2013, 02:46 AM   #5
A pause for the COZ
Senior Member
 
Join Date: October 11, 2012
Location: Braham, Minnesota
Posts: 347
I have no experience loading that light of a bullet. But you may also consider your case necks.
The more times you re-size/ fire a piece of brass. The case necks get work hardened. They dont expand like they once did nor contract like they once did.

May be in need of annealing????

A pause for the COZ is offline  
Old March 24, 2013, 12:43 PM   #6
A_Gamehog
Senior Member
 
Join Date: February 9, 2009
Location: Central Oregun
Posts: 559
I have the Nosler reloading manual 7th ed.

I load for the AR-15 also, Nowhere in that manual does it state "Crimp" this bullet. Unless you have a full auto M-16 don't.

By crimping this bullet in this instance you will deflect metal because it has no indentation area on this bullet.

Overkill for this application in my Opinion. It also increases pressure!
__________________
"Happiness is knowing the Barred Owl is Eating the Spotted Owl and environmentalists are watching Nature take it's course"
A_Gamehog is offline  
Old March 25, 2013, 07:03 AM   #7
stnosc
Member
 
Join Date: September 13, 2012
Posts: 41
First of all, like a couple of others asked, did you resize your brass first?

Next, get yourself a reloading manual if you don't have one and read it. Would recommend the Nosler manual if you're loading Nosler bullets.

Sounds like your new at this. Please study, study, study before attempting to go further.
stnosc is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 09:33 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.07019 seconds with 9 queries