The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > Handloading, Reloading, and Bullet Casting > Bullet Casting

Reply
 
Thread Tools
Old January 17, 2013, 01:54 AM   #1
MDS
Senior Member
 
Join Date: September 9, 2005
Location: Ohio
Posts: 486
suggstion for luber

I'm thinking of trying my hand at casting. Could someone recommend a luber sizer? I'm thinking one is going to run me around 180$. Is there anything with a little less cost. I've never shot bullets with alox? So I'm kind of leary of it.
MDS is offline  
Old January 17, 2013, 04:48 AM   #2
iraiam
Senior Member
 
Join Date: September 6, 2012
Location: Lakewood, CO
Posts: 861
Lee makes a much cheaper system with stand alone sizing dies and liquid alox that is applied after sizing, but i don't really like it, others seem to have good luck with it.

I use the RCBS luber/sizer, it could use a heater on it for an upgrade to keep the stiffer lubes soft when sizing/lubing, other than that I like it just fine, I tend to drive my lead pretty hard, I have had better luck with the harder wax-ish type lubes.
__________________
NRA Lifetime Member Since 1999

"I ask, sir, what is the militia? It is the whole people except for a few public officials." George Mason
iraiam is offline  
Old January 17, 2013, 02:19 PM   #3
MDS
Senior Member
 
Join Date: September 9, 2005
Location: Ohio
Posts: 486
Thanks, I think the RCBS is the one I looked at.
MDS is offline  
Old January 17, 2013, 03:54 PM   #4
Rottweiler
Senior Member
 
Join Date: January 30, 2001
Location: Texas Hill Country
Posts: 355
If you are looking to cast and size a LOT of bullets (1000+ ) I'd recommend a Star sizer. Star went out of business a few years ago but Magma Engineering bought the design and now makes the same sizer. Best I can desctibe it is comparing a Star to a RCBS,Lyman, Redding, ect. is it's like comparing a single stage press to a progressive press.

I made the switch to a Star a few years ago. I went from sizing a coffee can of bullets a day to a coffee can in about an hour and a half. Money well spent in my opinon.
__________________
Texas - envied by lesser states since 1845
Rottweiler is offline  
Old January 17, 2013, 04:07 PM   #5
jaguarxk120
Senior Member
 
Join Date: February 28, 2008
Location: Michigan
Posts: 1,926
The Star sizer is the best way to go even if your not making 1,000's of bullets. www.bufaloarms.com has Lyman, Saeco, and RCBS equipment.

If you just want to shoot chunks of lead down range-- then go cheap. BUT if you want the best accuracy out of your guns then go first class.
jaguarxk120 is online now  
Old January 18, 2013, 01:49 AM   #6
MDS
Senior Member
 
Join Date: September 9, 2005
Location: Ohio
Posts: 486
Thanks for the help guys. I will probably go cheaper for now until I see how much I'm going to get into it.
MDS is offline  
Old January 18, 2013, 07:24 AM   #7
GP100man
Senior Member
 
Join Date: August 1, 2007
Location: Tabor City , NC.
Posts: 1,912
Good move MDS

1 thing to think `bout is the dies for the star are expensive (see lathesmith over at castboolite.com) he makes dies for the Star , but once your set up production is`nt the problem.

Dies are more plentiful for the rcbs & lyman (beware altered used 1s) but production is cut by 2 thirds!!

& if you enjoy reloading ,you`ll LOVE casting !!
__________________
GP100man
GP100man is offline  
Old March 22, 2013, 03:05 AM   #8
A pause for the COZ
Senior Member
 
Join Date: October 11, 2012
Location: Braham, Minnesota
Posts: 311
Pan lubing, Then size with a LEE sizer is cheap enough. I still do this quite a bit. Push through sizing is the way to go.

I have a RCBS LAM 2, Its ok I guess. Some times I get ****** at it.

Then I got a used Star. This is they way to go, if you can swing the ging.
Push through with lubing. Awesome!!!!

I dont usually do more than a few hundred at a time but its still nice to be done no muss no fuss in 10 minutes.
Heck wife does not even know I disappeared, I am back so fast.

A pause for the COZ is offline  
Old March 22, 2013, 12:11 PM   #9
CS86
Senior Member
 
Join Date: February 28, 2012
Location: South Dakota
Posts: 217
If you want to go cheap use a $20 lee push through die and tumble or pan lube. Each has there own method but would be something cheap to start with. If you want to know a lot about casting go to Cast Boolits web site. They are a great wealth of information for casters.
CS86 is offline  
Old March 22, 2013, 04:45 PM   #10
dahermit
Senior Member
 
Join Date: October 28, 2006
Location: South Central Michigan...near Ohio, Indiana.
Posts: 3,505
Lyman and RCBS lube/sizers use the same dies and top punches. I have used both, and like the Lyman better because of the ratchet type of pressure handle. I never liked the slide-though pressure handle on the RCBS and returned to the Lyman. Starr is a good lube/sizer but the machine itself is costly as are the dies.

Whoops! Addendum: It would seem that others did not like the RCBS push-through pressure handle inasmuch as they seem to have adopted the Lyman-style ratchet.
__________________
Sometimes you get what you pay for, sometimes you only pay more for what you get.
Three shots are not a "group"...they are a "few".

If the Bible is the literal, infallible, unerring word of God...where are all those witches I am supposed to kill?

Last edited by dahermit; March 22, 2013 at 04:53 PM.
dahermit is offline  
Old March 24, 2013, 07:41 AM   #11
YARDDOG(1)
Senior Member
 
Join Date: October 24, 2008
Location: GATOR COUNTRY HA HA HA!
Posts: 679
I cast for 4 cal,, Only size 2 & use Lee push through sizers.. I use a mix of 45-45-10 of alox,JPW & minneral spirts ; ) PS I use 2 cal as cast
Y/D
__________________
There's a GATOR in the bushes & She's Callin my name
>Molly Hatchett<
YARDDOG(1) is offline  
Old March 24, 2013, 08:09 AM   #12
ronz
Senior Member
 
Join Date: January 12, 2012
Location: milwaukee wi
Posts: 220
just got a rcbs still has the rod on top (must of been old stock)
after getting it wish I never tried pan lubing
well worth the money
can size alot in a short time
ronz is offline  
Old March 24, 2013, 01:36 PM   #13
David Bachelder
Senior Member
 
Join Date: August 23, 2011
Location: Trinity, Texas
Posts: 616
I use Alox exclusively. I like it and use it for all of my pistol bullets. It does seem to smoke a lot though. I have learned that a little dab will do ya.

I guess thats good?
__________________
David Bachelder
Trinity, Texas
I load, 9mm Luger, 38 and 40 S&W, 38 Special, 357, 45ACP, 45 Colt, 223, 243 and 30-06
David Bachelder is offline  
Old March 24, 2013, 02:05 PM   #14
m&p45acp10+1
Senior Member
 
Join Date: May 3, 2009
Location: Central Texas
Posts: 3,307
I have never sized a bullet in the 4 years I have been casting. I shoot mine as cast lubed with Lee Liquid Allox. I put the bottle in a glass of hot water (hot to the point if you put a finger in you would take it out becasue it is hot, though not burn you hot.) I shake the bottle, when it feels like it is thin, I put a dab in a repurpoused butter bowl. Swish around a bit. Dump on a paper plate. I let them dry for about 3 days or so. I then load them, and shoot them. I cast for 3 hand gun, and 1 rifle caliber. They shoot great and do not lead up my barrels at all.
__________________
No matter how many times you do it and nothing happens it only takes something going wrong one time to kill you.
m&p45acp10+1 is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 10:59 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.08990 seconds with 9 queries