The Firing Line Forums

Go Back   The Firing Line Forums > The Hide > The Dave McCracken Memorial Shotgun Forum

Reply
 
Thread Tools
Old October 6, 2012, 12:46 PM   #1
MR.G
Senior Member
 
Join Date: July 20, 2001
Posts: 605
Mossberg feed tube spring

Can someone tell me how long a Mossberg 500 can be kept loaded before the feed tube spring becomes weak? I have a 500 with the eight shot tube that is kept loaded for HD and seldom fired.
MR.G is offline  
Old October 6, 2012, 01:44 PM   #2
Virginian-in-LA
Senior Member
 
Join Date: February 11, 2012
Location: Evangeline, LA
Posts: 761
Forever. Modern coil springs do not lose strength being kept in static loading.
Virginian-in-LA is offline  
Old October 6, 2012, 03:00 PM   #3
Slopemeno
Senior Member
 
Join Date: January 19, 2007
Posts: 2,344
I left mine loaded for 20+years, with the occasional unloading to transport it to the field. Is the spring sofer now? Yes. Does it still work? Yes.

Can you change the spring out? Yes. Is it hard? No. Wolf Springs has them.
Slopemeno is offline  
Old October 6, 2012, 03:43 PM   #4
MR.G
Senior Member
 
Join Date: July 20, 2001
Posts: 605
I would just order a new spring from Wolf, but the feed tube doesn't want to unscrew.
MR.G is offline  
Old October 6, 2012, 04:17 PM   #5
cajun47
Senior Member
 
Join Date: May 28, 2007
Location: swamp people
Posts: 539
channel locks
cajun47 is offline  
Old October 6, 2012, 04:34 PM   #6
Slopemeno
Senior Member
 
Join Date: January 19, 2007
Posts: 2,344
The mag tube is thin metal except at the very end where the barrel attaches. There it's thick for about 1/2". You want to use a strap wrench, or , as I did, wrap a piece of brass around it and grab it (carefully) with vice grips. Mine turned out very easily.

Remove the tubes, remove the follower and spring. Clean the interior of the mag tube, since you'll only get this chance every 30 years or so...

Insert the new spring and follower, put some low strength Loc-Tite on the threads, and reassemble.

This is a good technique to know, as mag tubes are easy to dent, and you should know how to replace one.
Slopemeno is offline  
Old October 6, 2012, 11:01 PM   #7
scottd913
Senior Member
 
Join Date: April 23, 2012
Location: Texas ... north of houston, east of el paso
Posts: 214
just had to replace mine because some idiot put a pencil in it for a plug.
i just disassembled it removed the forend and put the receiver between my legs and twisted the tube off with my hands. the spring i found at www.midwayusa.com for $3.99 plus shipping...good luck
scottd913 is offline  
Old October 7, 2012, 07:02 AM   #8
Pistolgripshotty
Senior Member
 
Join Date: September 19, 2012
Location: Somewhere out there
Posts: 184
You should be fine...just every 4 months or so it would be a good idea to cycle a few shells to keep some kind of spring pressure. You don't wanna have to need your shotgun and your spring is too weak to load the chamber. Good luck!
__________________
12 Gauge Fury!
Pistolgripshotty is offline  
Old October 7, 2012, 02:06 PM   #9
drail
Junior member
 
Join Date: February 2, 2008
Posts: 3,150
If you don't know how old your mag spring is or who made it buy a new one from Wolff. The mag spring is just about the most critical part in a pump gun. Most people figure out that they need a new mag spring when the gun starts to misfeed on the last couple of rounds. Don't wait that long. Just replace it for a few bucks. When you do you'll immediately notice how much more force is required to insert the first round into the mag. That's what you want to feel. If you're going to keep this gun loaded for years at a time consider downloading it by one round. The spring will last much longer than it will if you load it full up. Most shells will begin to swell long before the spring starts to weaken. Change them out once a year.
drail is offline  
Old October 7, 2012, 03:00 PM   #10
TheKlawMan
Junior member
 
Join Date: June 23, 2009
Location: Orange County, CA
Posts: 2,149
Dave McC's post elsewhere reminded me of an issue. Consider that while modern coil springs may not lose strength from being stored compressed, shot shells may become distorted if kept stored in a fully loaded tube. Hence, you might want to keep one less than max in the mag.
TheKlawMan is offline  
Old March 16, 2013, 03:53 PM   #11
unkster
Junior Member
 
Join Date: September 23, 2007
Location: Hudson Valley area NY
Posts: 1
Mag Spring

Had to order a new spring for my Mossberg 500c...the last round would not chamber, keeps falling out the bottom. I don't have the new spring as of yet, but I can't get the feed tube loose and don't want to damage it. Is there a tool with a locknut that goes into the feed tube so you can use a wrench to remove it. Seems like a good idea if you can match up the threads of the feed tube.
unkster is offline  
Old March 17, 2013, 10:01 AM   #12
hogdogs
Staff In Memoriam
 
Join Date: October 31, 2007
Location: Western Florida panhandle
Posts: 11,069
Quote:
channel locks
If you can't find a large rock and sledge hammer, the Channel Locks or Vise Grips would be your next option unless damage is to be avoided... at that time, go get a strap wrench and give that a try... If it is still not giving up... Get a heat gun or super good hair dryer and heat that area well to break any loc-tite loose etc...

If neither the gun or dryer is available, completely tear down the gun and put magtube/receiver assembly in the oven at 200 or so to get it hot...

Brent
hogdogs is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 06:09 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.08809 seconds with 9 queries