The Firing Line Forums

Go Back   The Firing Line Forums > The Hide > The Dave McCracken Memorial Shotgun Forum

Reply
 
Thread Tools
Old March 9, 2013, 12:06 AM   #1
higgscharger
Member
 
Join Date: February 26, 2013
Posts: 46
Mossberg 85 - Shell size?

I recently bought an old MOssberg 85 20 ga bolt action shotgun.

The bolt moves reasonably well for a 70 year old gun, but when i try put a shell through it the bolt will not close all the way.

I pulled the bolt out to try and figure out why. With the bolt out of the gun, i checked the size of the shell in the bolt. Turns out, the brass is larger than the depression on the bolt face around the firing pin. One side of the brass drops in, but the other side sits on top of the rim.

Has the size of a 20 ga shell changed since this was manufactured in the 1930s? Are there particular shells that have a slightly smaller circumfrence that will fit this gun?

OR...

Am i missing something else entirely?

Thanks for the help.
higgscharger is offline  
Old March 9, 2013, 09:54 AM   #2
PetahW
Senior Member
 
Join Date: September 19, 2008
Posts: 4,679
.

Not AFAIK.

Have you inspected the rim recess & extractor hook for a crud build up, and/or tried a different brand shotshell ?


.
PetahW is offline  
Old March 9, 2013, 04:35 PM   #3
BigD_in_FL
Junior member
 
Join Date: December 20, 2012
Location: The "Gunshine State"
Posts: 1,981
You trying to put a 2.75" in a 2.5" hole?
BigD_in_FL is offline  
Old March 9, 2013, 05:39 PM   #4
Virginian-in-LA
Senior Member
 
Join Date: February 11, 2012
Location: Evangeline, LA
Posts: 771
Unfired shotshells will fit in a chamber that is not designed for them: i.e. a 3" unfired shell will drop right in to a 2-3/4" chamber. But, when fired the crimp will extend past the chamber area and could increase pressures.
I do not know what is going on with the OP's gun. The extractor is spring loaded so it will push shells to one side outside the gun.
Virginian-in-LA is offline  
Old March 10, 2013, 07:40 AM   #5
higgscharger
Member
 
Join Date: February 26, 2013
Posts: 46
Working off memory, i'll do some careful looking when i get home, but if i recall correctly....


I did check the rim recess pretty well and there was not excessive crud. Not pristine, but nothing to explain this. However, there could be something right at the breech preventing the shell from seating properly in the chamber. I'll have to look more carefully at this.

I tried two brands of shells, i don't recall which they were though. Neither worked.

Is the 85 a 2 1/2 only? I thought it would accept 2 1/2 or 2 3/4?

Regardless, as Virginian said, the shells seem to fit fine, just the bolt won't lock into place. I'll check these things out when i get home and update.
higgscharger is offline  
Old March 10, 2013, 02:01 PM   #6
higgscharger
Member
 
Join Date: February 26, 2013
Posts: 46
Alright, a bit more information.

First, this is a Mosssberg Model 85, not an 85A-D.

According to here (which may or may not be accurate, but it is the best I can really find): http://home.epix.net/~damguy/mossber...gun_models.htm

the Model 85 take 2 1/2 and 2 3/4 shells.

Realized that I didn't try two different brands of shells. BOth were winchester, just one was AA Heavy Target Load, one was Super X Lead Shot. So, I'll need to try a different brand.

Going downstairs to clean the bolt face and breech really good, see if that helps.
higgscharger is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 07:37 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.05754 seconds with 9 queries