The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > Gear and Accessories

Reply
 
Thread Tools
Old February 18, 2013, 06:15 PM   #1
ZombieHunterD
Junior Member
 
Join Date: January 20, 2012
Posts: 7
mossberg ported barrel and recoil pads

So im planning on purchasing a mossy 500 turkey thug, as an all purpose type shotgun. It goes for $300 at academy. there happen to be one last time i went so i was looking at it and noticed the 24" barrel was ported. To people that have experience with these types of barrels, is it alot more loud than a nonported? Im not here to discuss if ported barrels actually work. If it turns out to be really loud i probably wont go with it.

Also, its a really light gun, so ill be picking up a better recoil pad. Ive heard good and bad things about limbsaver. And im also looking at the p. decelerator.
My question is, do the prefit and slip on version cushion the same amount against felt recoil or is one better that the other?

thanks guys
ZombieHunterD is offline  
Old February 21, 2013, 09:52 AM   #2
RonR6
Senior Member
 
Join Date: February 2, 2013
Location: South Eastern PA
Posts: 108
I had the 24" rifled barrel for my 500 ported and it does help
with the muzzle climb of the slugs. As far as noise, the porting
does not make a difference. My Weatherby Accumark has a accubrake
and that does make the shot excessively louder
because the ports cut in it direct the gases back towards the
shooter to help with recoil
RonR6 is offline  
Old March 4, 2013, 09:22 PM   #3
bamaranger
Senior Member
 
Join Date: October 9, 2009
Location: North Alabama
Posts: 4,441
Mossberg

I've just ordered a prefit Limbsaver for an 835. The slip over model seemed to goofy looking to me, and I am sure I could loose it off the butt w/o to much trouble given my luck and ability to mess up.

What little online checking I did seemed to show that folks liked the Limbsavers more than the Pach's. There was some dispute about fit with the 500's. Make sure you get a prefit that's intended for a synthetic stock, not a wood one, for the 500 series.

I can't say that the ports on our 835 make it any louder. I do think a shotgun barrel any shorter than 24 inches seems louder, as it's closer my ears!

The alloy receivered Mossbergs have a reputation as kickers with 3" and 3.5" shells. But standard velocity 2.75's are milder for most folks. I think the porting and hi-tech pad will make your 500 very shootable.
bamaranger is offline  
Old March 4, 2013, 10:27 PM   #4
BigD_in_FL
Junior member
 
Join Date: December 20, 2012
Location: The "Gunshine State"
Posts: 1,981
VERY LOUD I shoot a target gun with ported barrels and I wish they made the gun without them. You can easily feel the concussion and the blast
BigD_in_FL is offline  
Old March 5, 2013, 08:01 AM   #5
ClydeFrog
Junior member
 
Join Date: May 1, 2010
Posts: 5,798
12ga stocks...

I'm not much into shotguns right now but I may get a Browning BPS or 870(left hand) shotgun.

For stocks, Id check into a Knoxx recoil reducer type(that I think is in camo & for the Mossberg line) or the new to-cool-for-school Magpul shotgun stock.

ClydeFrog
www.blackhawk.com www.uscav.com www.magpul.com www.deltaforce.com www.natchezss.com www.midwayusa.com www.grafs.com
ClydeFrog is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 06:47 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.07640 seconds with 9 queries