The Firing Line Forums

Go Back   The Firing Line Forums > The Hide > The Dave McCracken Memorial Shotgun Forum

Reply
 
Thread Tools
Old September 27, 2011, 08:37 PM   #1
pops6116
Junior Member
 
Join Date: September 27, 2011
Posts: 3
Charles Daly 12 gauge, pistol grip

I have a Charles daly 12 gauge pump action model # CDFG 3010. I am trying to find a rear pistol grip that is compatible? any suggestions? the manufacturer is/ was, KBI out of Pa.

Last edited by pops6116; September 28, 2011 at 10:20 AM. Reason: added information
pops6116 is offline  
Old September 27, 2011, 11:24 PM   #2
Lee Lapin
Senior Member
 
Join Date: September 7, 2004
Location: SE NC
Posts: 1,238
Charles Daly was a reseller of imported guns, not a manufacturer. And they're out of business now. If there was ever a chance of finding what you're looking for, I'd guess that it's a lot slimmer now. If you can find out what company actually made your gun, that might give you a lead for what you want. I wish you the best of luck in your quest.

When us oldpharts tell folks over'n'over'n'over again to buy a commonly available currently manufactured American pumpgun (like a Remington 870 or Mossberg 500/590), wide availability of parts and accessories is one of the major reasons for offering that advice...

lpl
__________________
Mindset - Skillset - Toolset. In that order!

Attitude and skill will get you through times of no gear, better than gear will get you through times of no attitude and no skill.
Lee Lapin is offline  
Old September 28, 2011, 10:23 AM   #3
pops6116
Junior Member
 
Join Date: September 27, 2011
Posts: 3
shoulda woulda and coulda

I should have gone with my first instinct and gotten a mossberg 500 series but, the gun was gift, SO.....
pops6116 is offline  
Old September 28, 2011, 10:45 AM   #4
FlyFish
Senior Member
 
Join Date: January 20, 2009
Location: Overlooking the Baker River Valley
Posts: 1,517
KBI was not a manufacturer, they only purchased the Charles Daly brand and imported guns to be sold under that name. Most recently, Daly pump guns were made by Akkar of Turkey and replacement stocks (assuming that's what you're looking for) for Akkar shotguns are available at Numrich.


link
FlyFish is offline  
Old September 28, 2011, 10:56 AM   #5
pops6116
Junior Member
 
Join Date: September 27, 2011
Posts: 3
an oldphart, but a newbee

thanks for the info.. I'll check it out
pops6116 is offline  
Old February 19, 2013, 01:41 PM   #6
RDW24
Junior Member
 
Join Date: February 18, 2013
Posts: 1
Charles daly pistol grip

Hello charles daly fans, any grip that fits a mossberg 500 will fit a c.d. Pump or semi-auto. There are two issues you will encounter. First - the stock fastening bolt for the mossberg is probably a 5/16x 18 thread and the stock fastening bolt for the c.d. Is 10mmx1.5 thread. The second issue - the neck on the c.d. Is a little larger than the neck of the mossberg therefore you will encounter a small ledge where the grip/stock meets the receiver. There are several products out there (grips/stocks) that many people are happy with. If you need parts for c.d. Go to numrich.com and look up the parts -- then call akkar at 305-593-9782 after 2 pm and ask for mark. C.d. Pistol grip part #1197190a (a pistol grip stock is also avail. But i do not have the part #)
RDW24 is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 04:46 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.06561 seconds with 9 queries