The Firing Line Forums

Go Back   The Firing Line Forums > The Hide > The Art of the Rifle: Semi-automatics

Reply
 
Thread Tools
Old January 27, 2013, 11:22 AM   #1
adamc
Senior Member
 
Join Date: January 3, 2013
Location: Stalingrad Connecticut
Posts: 216
Bore scope alignment tool for ruger 10/22 ?

Bore scope alignment tool for ruger 10/22 ?

A previous thread got me interested in a scope for my 10/22.
I saw a borescope tool($39) and a couple of scopes ( $75 and less to $36)
in wally, but
I have never had good luck with the cheap wally stuff

anything good but NOT a million $$$$ mybe useful in other guns as well would be a plus.
adamc is offline  
Old January 27, 2013, 11:47 AM   #2
Art Eatman
Staff Lead
 
Join Date: November 13, 1998
Location: Terlingua, TX, USA
Posts: 22,540
I'm lazy and cheap. For sighting in any semi-auto, I made a target from a scrap of 1/4" plywood and a 12" piece of 2x4. Nail the plywood to the end of the 2x4. For targets, I just use a Pentel and draw a horizontal line on a sheet of typing paper and three vertical lines. Masking tape holds the paper to the plywood.

I set up at ten yards and get centered and an inch or two low. It's pretty easy to get on the paper and then get a better alignment. Then, go to 25 yards and get centered. For any centerfire, then, at 100 yards I'm commonly around three inches high and within an inch or two of vertical center.
__________________
You're from BATFE? Come right in! I use all your fine products!
Art Eatman is offline  
Old January 28, 2013, 10:12 PM   #3
wyobohunter
Senior Member
 
Join Date: August 21, 2008
Location: Back in Wyoming
Posts: 1,125
+1 Art- no need to bore sight. Just start your sight in session very close. It is cheaper to pop off a few extra .22 cartridges then to buy a dedicated tool. I do the same with all semi-autos. With the bolt guns I literally bore sight by mounting the gun to something, center the target in the bore and adjust the scope. That will easily get you on paper at 100 yds.
wyobohunter is offline  
Old January 29, 2013, 03:37 PM   #4
sholling
Senior Member
 
Join Date: May 18, 1999
Location: Hemet (middle of nowhere) California
Posts: 4,260
A bore sight just gets you on paper without wasting ammo but 22, even match 22 is cheap.

As for scopes I strongly recommend investing in good quality scopes and you won't find one for less than $100. You'll also want to match the scope with intended use and for a hunting/plinking rifle a fixed 4x like a Weaver RV4 4x28 rimfire scope or a variable power RV7 2.5-7x28 rimfire scope are excellent choices. Both offer good glass and rugged construction that should last you a lifetime. If your interests run more to target shooting than hunting then a Mueller APV 4.5-14x40 is a decent if light duty scope to get started in target shooting for cheap (~$130) but the crosshairs are a tad thick.
__________________
Proud Life Member: National Rifle Association, California Rifle & Pistol Association, and the Second Amendment Foundation.
Annual Member: Revolutionary War Veterans Association (Project Appleseed) and the Madison Society.
sholling is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 08:49 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.07436 seconds with 9 queries