Revolver Loading stand - Page 2

deerslayer303 · January 17, 2013, 11:00 PM

^^^ I'm working on making you a patch Beagle

Beagle333 · January 17, 2013, 11:05 PM

BirchOrr · January 24, 2013, 06:20 PM

Built this several years ago out of scrap oak I had laying around for my Uberti/Colt/Walker.

Loading stand.jpg

Works very well! (note the felt for the barrel & grip and the hammer notch to keep it stable).

Birch

maillemaker · January 29, 2013, 01:35 PM

Wish I had seen this thread earlier.

I just spend $35 on a cylinder loader from S&S Firearms. It's junk.

Any of these loaders that swing the ram on an arc will not seat bullets squarely into the cylinder. There is no provision for adjusting the position of the cylinder, either, so my ram doesn't even start off square.

I'm liking the Black Dawge loader mentioned above. It has adjustments for the cylinder position and the ram moves on a straight line.

Steve

Logan5579 · January 29, 2013, 02:44 PM

I've got one on order, should show up soon. I'll post my results after I get to try it out.

Logan5579 · February 2, 2013, 12:35 PM

My loader showed up thursday and I didn't get to give it a try til yesterday...it's been snowing and raining and cold here, but I finally caught enough of a break to get out in the yard for a few minutes and fire a few shots (18 shots was all I took the time to shoot, I hate the cold). I bought this from ebay, the sellers name is deanflip7,
http://www.ebay.com/itm/BRAND-NEW-BL...item27cf3ae003
hope this link works...

I think that this is the same guy from powder inc. (black dawge) at this link:

http://www.blackdawgecartridge.com/c...yl_loader.html

But I really like the loader, it's built tougher than the ones I found at cabela's and it doesn't load in an arc like some people have complained about. The ram is built to press straight down so it should load a conical straight in...I haven't tried them yet because I shot all mine up and haven't gotten to cast any new ones yet.

I mounted the loader on a piece of 3/4in ply that I sanded, routered the edges to a round over, and wiped down with mineral oil.

[IMG]

[/IMG]
[IMG]

[/IMG]

and I went out and shot a few round balls...the flyers are my fault, jerked the trigger, in too much of a hurry because it was getting dark on me

[IMG]

[/IMG]

So far no problems and I like being able to load off the gun, at first pass it seems to be quicker than using the built in ram because I can set six balls in place and ram them down one right after the other.

TomADC · February 2, 2013, 01:02 PM

Looking good I like the bowling pin, I tried the real ones years ago visiting my brother in law, my hi power would knock them over but not off the table they would just spin! The old 1911 cured that, be fun to try with a C&B 44.

deerslayer303 · February 4, 2013, 12:44 AM

Nice, I got the TOP loader from Straight shooter. I'm about to die to try it out. I gotta get my but in gear and cast some round ball.

January 17, 2013, 11:00 PM	#26
deerslayer303 Senior Member Join Date: January 10, 2011 Location: McMinnville TN Posts: 1,116	^^^ I'm working on making you a patch Beagle __________________ "You're so drunk you cant hit nothin, In fact you're probably seeing double"...."I have TWO GUNS one for each of ya"

January 24, 2013, 06:20 PM	#28
BirchOrr Senior Member Join Date: November 25, 2012 Location: Eaton Rapids, MI Posts: 204	Simple loading stand Built this several years ago out of scrap oak I had laying around for my Uberti/Colt/Walker. Loading stand.jpg Works very well! (note the felt for the barrel & grip and the hammer notch to keep it stable). Birch __________________ “A man who opens a case in hunting camp and lifts out a single-shot BP rifle makes a statement about himself. It may be quite unconscious, or it may be pure egotistical one-upmanship, but it does project the image of a superior marksman and a hunter of above-average skills.”

January 29, 2013, 02:44 PM	#30
Logan5579 Senior Member Join Date: January 9, 2013 Location: Tennessee Posts: 102	I'm liking the Black Dawge loader mentioned above. It has adjustments for the cylinde I've got one on order, should show up soon. I'll post my results after I get to try it out. __________________ Beware the man with one gun, he knows how to use it

February 2, 2013, 12:35 PM	#31
Logan5579 Senior Member Join Date: January 9, 2013 Location: Tennessee Posts: 102	My loader showed up thursday and I didn't get to give it a try til yesterday...it's been snowing and raining and cold here, but I finally caught enough of a break to get out in the yard for a few minutes and fire a few shots (18 shots was all I took the time to shoot, I hate the cold). I bought this from ebay, the sellers name is deanflip7, http://www.ebay.com/itm/BRAND-NEW-BL...item27cf3ae003 hope this link works... I think that this is the same guy from powder inc. (black dawge) at this link: http://www.blackdawgecartridge.com/c...yl_loader.html But I really like the loader, it's built tougher than the ones I found at cabela's and it doesn't load in an arc like some people have complained about. The ram is built to press straight down so it should load a conical straight in...I haven't tried them yet because I shot all mine up and haven't gotten to cast any new ones yet. I mounted the loader on a piece of 3/4in ply that I sanded, routered the edges to a round over, and wiped down with mineral oil. [IMG][/IMG] [IMG][/IMG] and I went out and shot a few round balls...the flyers are my fault, jerked the trigger, in too much of a hurry because it was getting dark on me [IMG][/IMG] So far no problems and I like being able to load off the gun, at first pass it seems to be quicker than using the built in ram because I can set six balls in place and ram them down one right after the other. __________________ Beware the man with one gun, he knows how to use it

February 2, 2013, 01:02 PM	#32
TomADC Senior Member Join Date: October 14, 2009 Posts: 377	Looking good I like the bowling pin, I tried the real ones years ago visiting my brother in law, my hi power would knock them over but not off the table they would just spin! The old 1911 cured that, be fun to try with a C&B 44. __________________ US Navy Retired,NRA Life Member,SASS member, Time magazine's Person of the Year 2006!

January 17, 2013, 11:05 PM	#27
Beagle333 Senior Member Join Date: January 7, 2012 Location: Back in the woods a piece Posts: 740

January 29, 2013, 01:35 PM	#29
maillemaker Senior Member Join Date: August 30, 2010 Posts: 564	Wish I had seen this thread earlier. I just spend $35 on a cylinder loader from S&S Firearms. It's junk. Any of these loaders that swing the ram on an arc will not seat bullets squarely into the cylinder. There is no provision for adjusting the position of the cylinder, either, so my ram doesn't even start off square. I'm liking the Black Dawge loader mentioned above. It has adjustments for the cylinder position and the ram moves on a straight line. Steve

February 4, 2013, 12:44 AM	#33
deerslayer303 Senior Member Join Date: January 10, 2011 Location: McMinnville TN Posts: 1,116	Nice, I got the TOP loader from Straight shooter. I'm about to die to try it out. I gotta get my but in gear and cast some round ball. __________________ "You're so drunk you cant hit nothin, In fact you're probably seeing double"...."I have TWO GUNS one for each of ya"