The Firing Line Forums

Go Back   The Firing Line Forums > The Hide > The Art of the Rifle: Bolt, Lever, and Pump Action

Reply
 
Thread Tools
Old January 19, 2013, 09:53 AM   #1
wnycollector
Senior Member
 
Join Date: April 22, 2007
Posts: 1,829
CZ 527 varmint scope mounting options

I'm picking up a CZ 527 varmint in 223 and I'm looking for a 30 mm one piece scope mount for it. I checked DNZ, but they don't have any CZ mounts. What is a solid mount for ~$100?

Last edited by wnycollector; January 19, 2013 at 10:01 AM.
wnycollector is offline  
Old January 20, 2013, 12:45 AM   #2
ch47gunner
Senior Member
 
Join Date: May 28, 2007
Location: Santa Cruz, Ca.
Posts: 165
Your 527 is set up to take 16mm dove-tail rings.
If you intend to use a one-piece mount, you will need to drill & tap the receiver.
I have a 527 and use Warne Maxima Permanent steel vertical split rings, it's a very solid set-up.
Should you decide to go ahead with a one-piece mount, I've used a couple of Ken Farrell mounts, on Savage varmint/tactical rigs, that I liked very well.

Link to Ken Farrell -
http://www.kenfarrell.com/CZ-527-VARMIT-1-0.html

Good luck,

Bruce

CZ527 Varmint w/ Bushnell Elite 4200 6-24x40 & Warne Maxima rings.
ch47gunner is offline  
Old January 20, 2013, 07:02 AM   #3
FALPhil
Senior Member
 
Join Date: September 10, 2007
Location: Racoon City
Posts: 933
CZ_Ringmounts_list_.pdf
This attachment has all the CZ ring mounts that I am aware of. On my 527 Varmint, I chose the CZ branded rings.
FALPhil is offline  
Old January 20, 2013, 08:47 AM   #4
Rimfire5
Senior Member
 
Join Date: January 2, 2009
Location: Northern Virginia
Posts: 464
I have two CZs with the dove tail mounts and after using the CZ rings on my .223 I found that the flat screw slots on the CZ rings were not easy to torque. I decided that I would go with Burris Signature rings with the plastic inserts and Torx screws on the rings for my CZ 550 in .30-06. You can get them in the dove tail mounts.

The rear ring on both the CZ and Burris ring sets have a lug that keeps the ring from slipping.
Either work fine and are very stable.
Rimfire5 is offline  
Old January 20, 2013, 06:35 PM   #5
Hunter Customs
Senior Member
 
Join Date: March 26, 2005
Location: Osborn, Missouri
Posts: 1,763
If you don't find the mount you want I have a pair of 30mm rings that fit the CZ 527 model rifles.
If you are interested in them you can e-mail at bob@huntercustoms.com .

Best Regards
Bob Hunter
www.huntercustoms.com
Hunter Customs is offline  
Old January 21, 2013, 09:48 AM   #6
wnycollector
Senior Member
 
Join Date: April 22, 2007
Posts: 1,829
Thanks for the help folks!
wnycollector is offline  
Old January 21, 2013, 02:28 PM   #7
mike7.62
Member
 
Join Date: May 25, 2012
Location: Down South
Posts: 89
I went with the Talley rings on my 527 and like them. I'm not sure they come in 30mm. Mine are 1" It want hurt to check. They are very nice rings.

Last edited by mike7.62; January 21, 2013 at 02:38 PM.
mike7.62 is offline  
Old January 21, 2013, 10:02 PM   #8
reynolds357
Senior Member
 
Join Date: December 10, 2012
Posts: 2,238
Talley makes good stuff. Made in South Carolina.
reynolds357 is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 04:16 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.08020 seconds with 10 queries