The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > Handloading, Reloading, and Bullet Casting

Reply
 
Thread Tools
Old January 16, 2013, 09:48 AM   #1
THERAVEN
Member
 
Join Date: February 24, 2009
Posts: 18
Reloading slugs

I want to get back into reloading shotgun shells. I want to do slugs. Can I use shot casings or do I need to use only slug casings.
THERAVEN is offline  
Old January 16, 2013, 10:06 AM   #2
paknheat
Senior Member
 
Join Date: October 17, 2006
Location: East Texas
Posts: 242
Interested in this myself, tagged for further interest .


Sent from my iPhone using Tapatalk
paknheat is offline  
Old January 16, 2013, 12:00 PM   #3
jrinne0430
Senior Member
 
Join Date: November 30, 2007
Location: Virginia
Posts: 154
You can use either. I use Winchester AA or Federal Gold Metal hulls when loading Lee 1oz slugs.
jrinne0430 is offline  
Old January 17, 2013, 07:30 PM   #4
Catfish
Member
 
Join Date: November 30, 2010
Posts: 87
I`m definately not a Lee fan, but I have a friend that is casting slugs with the new Lee slug and is haveing real good luck with them. He is loading AA hulls and the AA wads.
Catfish is offline  
Old January 17, 2013, 10:51 PM   #5
oldandslow
Senior Member
 
Join Date: October 2, 2007
Posts: 561
tr, 1/18/13

I've spent the past two years experimenting with different 12 gauge slug loads and finally found what works for my pig hunting at ranges of less than 100 yards in heavy brush.

First step is to take a look at the www.castboolits.gunloads.com shotgun loading subforum and also over at www.shotgunworld.com in the slugshooters subforum. Both are very helpful. Next, for supplies look at www.ballisticproducts.com they have almost everything you'll need to load slugs.

I've tried the Lyman 525 grain slug, the BPI shuttlecock slug, the Foster's slug and the Gualandi fullbore slug with attached wad. All were in a smoothbore barrel. I've tried multiple hulls, wad and shot card combinations and even filling the rear cavity of some of the slugs with epoxy resin but only got good results (sub-3" 50 yard groups) with the Gualandi slug. Since these come from Italy I didn't want to depend on a supplier half a world away from my location.

The final best answer was to order a slug mold from Tom at www.accuratemolds.com. I got the 770 grain slug mold and figured out a magic load with Blue Dot (thanks to the CB and SGW forum members) that groups well and goes in one side of a wild pig and out the other leaving a 0.730" hole. I changed out the barrel to a rifled one after getting frustrated with the smoothbore.

Take a look at the above sites (which also have info on the Lee slug), and see if it helps you. Good luck.

best wishes- oldandslow
oldandslow is offline  
Old January 18, 2013, 12:05 AM   #6
Sure Shot Mc Gee
Senior Member
 
Join Date: January 2, 2012
Posts: 2,094
Might want to visit Ballistic Products web site for a looks see. Afterwards. You just may want to try roll crimping your slugs.
__________________
Heartland of gun country. Fishing too.
Sure Shot Mc Gee is offline  
Old January 18, 2013, 08:35 AM   #7
kraigwy
Senior Member
 
Join Date: June 16, 2008
Location: Wyoming
Posts: 9,475
I believe in keeping it simple. About the only thing I use shotguns for now days is 3 gun. I use an old Remington 870 Police Riot gun with an 18 inch smooth barrel.

In three gun, you don't shoot that far, you are required to shoot bird shot, slugs and buck shoot.

Like I said, I keep it simple, I use WW AA Hulls, AA wads, and a Mec 1 oz charge bar.

I load 1 oz of 8 shot, and Lee's 1 oz slug, and I use a Lee round ball mold that makes .319 balls at 48 grns, which I stick 9 into the same AA hulls and wads.

Recoil is the same across the board, the buck shot and bird shot pattern plenty good enough for the distance we shoot, and I have no problem hitting an 8 inch circle with my slug loads at 50 yards (again, within the distances we shoot).

The only modification I do to the above loads is I use a magic marker to mark which shell is buck shot or slugs.

I have other charge bars for my Mec 600 If I decide to go bird hunting, but there aren't many birds around here. Or I have the set up for trap and skeet loading if I decide to get back into those games.

You really don't have to get all fancy with slug loading.

Some people deer hunt with shot guns, If I was to do that I have faith in my slugs, but I'd probably put a bit more powder behind my buck shot loads.
__________________
Kraig Stuart
CPT USAR Ret
USAMU Sniper School Oct '78
Distinguished Rifle Badge 1071
kraigwy is offline  
Old January 18, 2013, 09:33 PM   #8
Xfire68
Senior Member
 
Join Date: March 31, 2010
Location: Communist State of IL.
Posts: 1,428
kraigwy, what powder and charge are you using?
__________________
NRA Life Member, SAF Member

www.aac300blackoutbrass.com A Veteran owned Business.
Xfire68 is offline  
Old January 19, 2013, 12:35 AM   #9
kraigwy
Senior Member
 
Join Date: June 16, 2008
Location: Wyoming
Posts: 9,475
I use the Mec #31 powder bushing throwing 18.5 grs. of Red Dot
__________________
Kraig Stuart
CPT USAR Ret
USAMU Sniper School Oct '78
Distinguished Rifle Badge 1071
kraigwy is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 04:44 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.08095 seconds with 9 queries