The Firing Line Forums

Go Back   The Firing Line Forums > Hogan's Alley > Handguns: The Revolver Forum

Reply
 
Thread Tools
Old January 6, 2013, 07:21 PM   #1
coolhand35
Junior Member
 
Join Date: September 20, 2012
Posts: 12
Taurus model 82 .38 special problem

I just bought a used model 82 from gander mountain. The reason i bought it is cause they had it at a good price. After purchasing it i went to the indoor range and put about 150 rounds through it. The problem i was having was sometimes when i would push the cylider in it would sometimes not want to go in smoothly so i had to force it in to lock like something was stoping it from going in but it did not happen every time. Also sometimes while i was firing it in double action it would sometimes be very hard to pull before it fired almost like it was hanging up and it also would happen every time. Has anyone heard of this issue or experienced themselves? If so any comments would be very appreciated...Thanx!!
coolhand35 is offline  
Old January 7, 2013, 02:37 AM   #2
warningshot
Senior Member
 
Join Date: October 7, 2009
Posts: 995
oh yea.

I've heard of multiple serious problems with Taurus revolvers before; even just a few more than you mentioned. Good Luck.
warningshot is offline  
Old January 7, 2013, 07:17 AM   #3
Kreyzhorse
Senior Member
 
Join Date: April 12, 2006
Location: NKY
Posts: 11,370
Possible fouling under the ejection star? Check that and clean it well. That may take care of the problem.

If that doesn't take care of it, Taurus often has issues with the forcing cone causing binding. My Taurus M85 had the same issues as you describe. After the issues and then dealing with Taurus's wonderful customer service, I no longer trusted the gun so I sold it.

Anyway, if a good cleaning doesn't work, try giving Taurus a call. Good luck.
__________________
"He who laughs last, laughs dead." Homer Simpson
Kreyzhorse is offline  
Old January 7, 2013, 08:10 AM   #4
PetahW
Senior Member
 
Join Date: September 19, 2008
Posts: 4,562
Now you know why the price was so "good" - a reason to buy on "quality", rather than on "price".

Just a clue - I once sold a brand-new, but troublesome, Taurus revolver - instead of dealing with the notorious Taurus Customer Service thing.

"IF" you're handy, dis-assemble it, & give the insides a good cleaning, being sure to inspect for little bits & shreds of metal left in there during manufacture, that were never cleaned out.


.
PetahW is offline  
Old January 7, 2013, 08:49 AM   #5
mega twin
Senior Member
 
Join Date: August 15, 2006
Posts: 424
If you don.t have a manual,I would get one before you take it apart,if you are not familiar with the procedure.
The Taurusarmed.net site has a lot of good info,and may have a tutorial for your gun.
Good luck,and keep us posted.
mega twin is offline  
Old January 7, 2013, 10:26 AM   #6
CajunBass
Senior Member
 
Join Date: May 6, 2005
Location: Chancellorsville, Virginia
Posts: 3,331
I've had revolvers that did the same thing. But they weren't Taurus. One was a Ruger, the other a Colt.

I'd give it a good cleaning. Someone else has mentioned cleaning under the ejector star. Someone else mentioned the forcing cone. Clean those well, especially the forcing cone. I've seen a build up of bullet lube and lead that would cause the cylinder to bind there. Clean the front to the cylinder well too. The Colt I mentioned, I had to take a brass brush (lightly) to the forcing cone area to get the crud off it. Never had a bit of trouble with it again.

Flush the internals with gunscrubber, and give it a few drops of oil. Put a drop or two on the ejector rod and hopefully, you'll be good to go.

I had one of those Taurus 38's back in the day. I forget the Model number, but it was an 80, 82...something like that. Fixed sight, more or less Model 10 copy. Good shooting gun, but man that thing had some UGLY grips.
__________________
For God so loved the world, that He gave His only begotten Son, that whoever believes in Him should not perish, but have everlasting life.
John 3:16 (NKJV)
CajunBass is offline  
Old January 7, 2013, 09:44 PM   #7
Budda
Senior Member
 
Join Date: November 7, 2011
Location: Earth
Posts: 441
Love my Taurus. 38 never had a problem and shoots better than my Smith bodyguard.
__________________
...They have the internet on computers now....-Homer Simpson-
Budda is offline  
Old January 9, 2013, 10:36 PM   #8
OkieCruffler
Senior Member
 
Join Date: July 9, 2001
Location: Denison Texas on the banks of Texhoma
Posts: 1,470
Give it a good cleaning if that doesn't fix it send it back to Taurus. I bought a 22 tracker awhile back that wouldn't turn the cylinder all the time when shooting. Sent it to Taurus expecting never to see it again with all the BS I've read online. Had it back in 8 working days, completely fixed, free of charge. Was so impressed I sent my 650 in to them. Nothing wrong with it other than it was getting alittle play in the cylinder after thousands of rounds of hot 357. Granted it took them 14 days on it but once again, returned good as new and free of charge.
__________________
John A. Monroe, Never Forgive, Never Forget, Blood Pays Blood
OkieCruffler is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 04:55 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2013 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.08269 seconds with 9 queries