The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > Handloading, Reloading, and Bullet Casting

Reply
 
Thread Tools
Old January 4, 2013, 12:02 AM   #1
TheDutchman19
Senior Member
 
Join Date: August 30, 2012
Location: So Cal
Posts: 105
Dremel for case prep?

Has anyone seen an adaptor that allows you to put your case prep bits and tools in a Dremel? I don't like how a 90 degree handle of a drill feels when doing those tasks. Is there a straight handheld drill motor that anyone has used?
TheDutchman19 is offline  
Old January 4, 2013, 08:06 AM   #2
10 Spot Terminator
Senior Member
 
Join Date: January 3, 2008
Location: Central Oregon
Posts: 346
Just google up Dremel tool chucks. Anything you could chuck up in a small drill will work.
10 Spot Terminator is offline  
Old January 4, 2013, 09:47 AM   #3
serf 'rett
Senior Member
 
Join Date: June 25, 2009
Location: Stuttgart
Posts: 1,284
Dremil tool is high speed but low torque. You may get it to work, but if you apply much pressure, it may not work for long. I use dremil tools for everything from wood carving to polishing feed ramps to sharpening lawn mower blades; however, I understand the limitations of this small tool.

A drill motor is designed for heavier loads. Ideally you would find some way of securing the drill.
__________________
A lack of planning on your part does not necessarily constitute an emergency on my part.
serf 'rett is offline  
Old January 4, 2013, 10:11 AM   #4
Unclenick
Staff
 
Join Date: March 4, 2005
Location: Ohio
Posts: 10,195
Agree. The Dremel is the wrong speed/torque combination. What you want is an straight handle electric screw driver. Low speed and high torque. Fit it with a hex bit chuck (a cheaper one can be had if your tools don't need a 3/8" capacity).
__________________
Gunsite Orange Hat Family Member
CMP Certified GSM Master Instructor
NRA Certified Rifle Instructor
NRA Patron Member
Unclenick is offline  
Old January 4, 2013, 10:16 AM   #5
Magnum Wheel Man
Senior Member
 
Join Date: July 26, 2006
Location: Southern Minnesota
Posts: 8,105
understand it's not an answer to you question, but I use an RCBS case prep center... allows me to do a couple jobs at the same time, since it has multiple heads
__________________
In life you either make dust or eat dust...
Magnum Wheel Man is offline  
Old January 4, 2013, 10:28 AM   #6
elkslayer4x5
Member
 
Join Date: June 30, 2006
Location: Lane County, Oregon
Posts: 66
You can secure your drill motor by wrapping a length of nylon webbing around it and clamping in a vise, or by screwing drywall screws into a piece of wood.
__________________
"Skin that one out, and I'll get ya another!
elkslayer4x5 is offline  
Old January 4, 2013, 11:01 AM   #7
tobnpr
Senior Member
 
Join Date: August 1, 2010
Location: Tampa Bay
Posts: 2,850
Far too high-speed...
Case prep is done by hand, or variable speed drills/screwdrivers on low rpm settings ( same a "case prep centers")

You're gonna risk removing too much material in a nanosecond at those speeds...
tobnpr is offline  
Old January 4, 2013, 02:28 PM   #8
wogpotter
Senior Member
 
Join Date: September 27, 2004
Posts: 2,950
An electric screwdriver is a much better tool to do this fairly slow &with a bucket load of torque. Just get whatever one you like & a 1/4" chuck adaptor to hex shaft from Lowes or Home Depot.
__________________
Allan Quatermain: “Automatic rifles. Who in God's name has automatic rifles”?

Elderly Hunter: “That's dashed unsporting. Probably Belgium.”
wogpotter is offline  
Old January 4, 2013, 07:30 PM   #9
oneoldsap
Senior Member
 
Join Date: September 16, 2009
Location: I live in the foot of the Green Mountains of Vermont
Posts: 1,584
I use a B&D cordless screwdriver , with a Lyman case prep kit . Works like a charm ! The Dremel is definately not the tool for the job .
oneoldsap is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 10:03 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.09854 seconds with 9 queries