The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > Handloading, Reloading, and Bullet Casting

Reply
 
Thread Tools
Old January 4, 2013, 12:36 AM   #1
browninghunter86
Senior Member
 
Join Date: November 14, 2011
Posts: 524
Lee Perfect Powder Measure

Just thought I would share my results with using this powder measure. Prepping my match loads and weighed 50 charges of Varget on my Gem Pro 250 scale that is calibrated and good to go. My charge weight is 44.2 gr. My findings are that out of 50 charges thrown, my average weight thrown was 44.17 gr, my ES was 0.55 and my SD was 0.15.

Not too bad for a powder thrower with it's price tag.
browninghunter86 is offline  
Old January 4, 2013, 12:49 AM   #2
Jimro
Senior Member
 
Join Date: October 18, 2006
Posts: 5,758
Nice, your ES is less than the +/- .3 grains where an OCW load can shine.

I've had good luck with the Lee PPM as well, even with IMR4064.

Jimro
__________________
"Gorsh" said Goofy as secondary explosions racked the beaten zone, "Did I do that?"

http://randomthoughtsandguns.blogspot.com/
Jimro is offline  
Old January 4, 2013, 12:51 AM   #3
Marco Califo
Senior Member
 
Join Date: April 4, 2011
Location: LA
Posts: 872
I concur. The PPM is certainly usable. I especially like the chart and powder densities they give. That is really handy in getting to your desired load. I have found the charts to be very accurate in predicting the volume setting required for a given charge, and steps upward.
__________________
........................................................
Marco Califo is offline  
Old January 4, 2013, 07:43 AM   #4
PawPaw
Senior Member
 
Join Date: December 24, 2010
Location: Central Louisiana
Posts: 3,115
I've had one since the '90s, but admit that I've never used it for rifle loads. It's my measure for pistol powders, but I've been very happy with it.
__________________
Dennis Dezendorf

http://pawpawshouse.blogspot.com
PawPaw is offline  
Old January 4, 2013, 04:48 PM   #5
dwhite
Senior Member
 
Join Date: September 2, 2007
Location: Wake County, N. Carolina
Posts: 291
Use mine for pistol too. I've been very pleased with it.

Only issue I've had is it leaks AA-7 like a sieve. Haven't
been able to get it to stop. Don't use a lot of it though
so it isn't a big problem.

All the Best,
D. White
dwhite is offline  
Old January 4, 2013, 09:48 PM   #6
amamnn
Senior Member
 
Join Date: May 13, 2006
Location: WA, the left armpit of the USA
Posts: 1,323
Check in again about this in a year or two.............
__________________
"If the enemy is in range, so are you." - Infantry Journal
amamnn is offline  
Old January 5, 2013, 10:10 PM   #7
Sport45
Senior Member
 
Join Date: May 25, 1999
Location: Too close to Houston
Posts: 4,081
Quote:
Check in again about this in a year or two.............
Why? Do you think powders will change?
__________________
Proud member of the NRA and Texas State Rifle Association. Registered and active voter.
Sport45 is offline  
Old January 6, 2013, 12:20 PM   #8
rdmallory
Senior Member
 
Join Date: February 10, 2009
Location: Deltona FL
Posts: 952
I use mine on my Dillon
rdmallory is offline  
Old January 7, 2013, 07:18 PM   #9
Kilroy08
Senior Member
 
Join Date: April 15, 2005
Posts: 166
I bought one when I got my Loadsmasher. It works well enough. At $45ish for the powder measure and charge die, it wasn't too bad since I wanted to keep my Uniflow by its self for if I want to do single stage stuff on the Rockchucker.

The only complaint I have is how it likes to pee powder all over the press. I'll stop, tune it back up, and go again. Half an hour later I'm back to using words best kept in private. Charge weights are consistent, it's just the granule or two of powder that seeps out adds up after a while. Kind of like my Jeep, it leaks enough to be a constant annoyance but not an actual problem.
Kilroy08 is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 11:31 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.07563 seconds with 9 queries