The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > The Smithy

Reply
 
Thread Tools
Old January 2, 2013, 05:48 PM   #1
MikeSD
Junior Member
 
Join Date: January 2, 2013
Posts: 5
Scope Mounting Question - Changing ring spacing

I have a Savage 93, .22 WMR. The stock scope mounting rails are short 1" rails about 5" apart.

The scope I have is a Leupold VX-2 3-9x33 Rimfire EFR. It's a nice scope but the eye relief is short (3.1" to 3.4" or thereabouts). If I mount the rings on the stock rails, I can't move the scope back far enough to get the most optimal placement to accommodate the short eye relief. The front ring is right up to the front of the tube and the rings can't be moved reward.

I'd like to be able to move the entire scope rearward about 1".

I've ordered an EGW rail, for this rifle. It won't allow the rear ring to be mounted any further back than the stock mounts. However, it will allow me to move the front ring backward 1". This would allow me to move the scope rearward that extra inch I need. What this would also do, however is make the ring spacing only 4" instead of 5".

I don't recall the actual spacing of the rings but it's about 5" or so, and this would be moving them closer by 1". What I'm wondering is if having the scope rings only 4" apart will cause any damage to the scope vs. the 5" spacing of a standard mount, due to vibration or recoil. The scope overall length is 11.6". It's only a .22 magnum but still I wonder. Any idea?
MikeSD is offline  
Old January 2, 2013, 06:57 PM   #2
PetahW
Senior Member
 
Join Date: September 19, 2008
Posts: 4,679
Don't worry - be happy (and shoot the snot out of it). .



.
PetahW is offline  
Old January 2, 2013, 08:28 PM   #3
MikeSD
Junior Member
 
Join Date: January 2, 2013
Posts: 5
The funny thing is, I only bought the rifle because I did an inventory of ammo and found 1400 rounds of .22 WMR and nothing to shot it in.

But looking at this rifle, I happened to take a look at the .17 HMR. Might get one of those too. I bought 7 of the mags for the .22 WMR and apparently the .17 HMR uses the same mags. So why not.

Funny how one thing leads to another. But it doesn't violate my rule that you can't have too much ammo or too many guns.
MikeSD is offline  
Old January 2, 2013, 11:29 PM   #4
srfisher3
Member
 
Join Date: November 3, 2012
Posts: 17
I would be most concerned (or perhaps the correct word is careful) about how tightly you torgue the rings to the scope if you're moving them. The tension you apply with the wrench will definitely apply more pressure on the tube than the recoil of the .22W. Its a quality scope for sure and totally made for the recoil of a .22. Be cautious when tightening the screws and you'll be just fine.
srfisher3 is offline  
Old January 3, 2013, 12:17 AM   #5
MikeSD
Junior Member
 
Join Date: January 2, 2013
Posts: 5
I used a torque driver to tighten the screws. I set the driver at a little under 20 in-lbs of torque, on the ring halves. I think I'm ok there. But good to know I'm worrying about nothing on the ring spacing.



When I get the new base, I'll move the scope back about 1". I'll just have enough room to avoid the ejection port.
MikeSD is offline  
Old January 3, 2013, 05:24 PM   #6
oneoldsap
Senior Member
 
Join Date: September 16, 2009
Location: I live in the foot of the Green Mountains of Vermont
Posts: 1,585
You need an extension ring for the front , they're in the Brownells catalog .
oneoldsap is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 10:35 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.07296 seconds with 9 queries