The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > Handloading, Reloading, and Bullet Casting

Reply
 
Thread Tools
Old December 8, 2012, 03:38 PM   #1
Stan Palmer
Junior Member
 
Join Date: November 26, 2012
Posts: 2
new to reloading,41 mag loads

Would like info. about a starting place for reloading 41 mag.
Thanks
Stan Palmer is offline  
Old December 8, 2012, 04:16 PM   #2
mrawesome22
Senior Member
 
Join Date: November 9, 2005
Location: Ohio, Appalachia's foothills.
Posts: 3,779
Lyman 49th.
mrawesome22 is offline  
Old December 8, 2012, 06:07 PM   #3
jepp2
Senior Member
 
Join Date: December 24, 2008
Location: Loveland, CO
Posts: 1,348
Do you have any reloading manuals? They are an excellent resource guide to the reloading process.

Concerning load data, I utilize Hodgdon's website since they cover loads for Hodgdon, IMR, and Winchester powders, they list starting and max loads, show pressure and the specifics of the load (primer type and barrel length). Lots of bullets are listed.

Some powders prefer magnum primers, some prefer a strong crimp.

You will save a lot of money loading for the 41 mag.
jepp2 is online now  
Old December 8, 2012, 06:08 PM   #4
Sevens
Senior Member
 
Join Date: July 28, 2007
Location: Central Ohio
Posts: 8,934
We can help a whole heckuva lot more if you can get more specific with your needs.

Need help with bullet choice? Technique? Equipment? Powder suggestions?
__________________
Attention Brass rats and other reloaders: I really need .327 Federal Magnum brass, no lot size too small. Tell me what caliber you need and I'll see what I have to swap. PM me and we'll discuss.
Sevens is offline  
Old December 8, 2012, 06:17 PM   #5
Mike Irwin
Staff
 
Join Date: April 13, 2000
Location: Northern Virginia
Posts: 36,074
Bullet

Powder

Primer

Case


Thats a good starting point.
__________________
"The gift which I am sending you is called a dog, and is in fact the most precious and valuable possession of mankind" -Theodorus Gaza

Baby Jesus cries when the fat redneck doesn't have military-grade firepower.
Mike Irwin is offline  
Old December 8, 2012, 07:12 PM   #6
m&p45acp10+1
Senior Member
 
Join Date: May 3, 2009
Location: Central Texas
Posts: 3,310
Lyman's Pistol and Revolver 3rd is a good one as well.

For bullets the 210 grain bullets work well in most .41 Mag guns as far as not having to change the sights, and shooting to point of aim.

For powders I have tried several, and have settled on two.

1. Trail Boss for cast lead general paper punching, and steel knock down targets. I shoot home cast LSWC using the Lee 210 grain TLSWC mold.

2. AA#9 For jacketed, and warm cast lead loads. I tried Alliant 2400 it worked, though was dirty even at warmer velocity levels. With jacketed loads it can get pretty darn close to where H-110 goes for velocity. It will allow for use of lead at warm velocity as H110 will not. It also very clean burning as well.

Note you are going to need to use a heavy roll crimp.

For bullets I have used several with good results. Though the majority of my shooting is with home cast lead.

Berry's 210 grain Plated FN work well. As do 210 grain Remington JSP.

For hunting I have a few Winchester Silver Tip 175 grain JHP. They did the job on several hogs quite well.
__________________
No matter how many times you do it and nothing happens it only takes something going wrong one time to kill you.
m&p45acp10+1 is offline  
Old December 8, 2012, 07:18 PM   #7
zxcvbob
Senior Member
 
Join Date: December 20, 2007
Location: S.E. Minnesota
Posts: 4,203
Quote:
I shoot home cast LSWC using the Lee 210 grain TLSWC mold.
I haven't reloaded much .41 Mag yet, but the one load I have tried is that bullet with 9.0 grains of Universal.

I inherited a Ruger Blackhawk .41 from my father in law, and it's pretty worn and loose -- so I don't like shooting full factory jacketed loads in it (besides, they are way too expensive.)
__________________
"The only way to stop a bad guy with a gun is with a good guy with a gun"
zxcvbob is offline  
Old December 8, 2012, 09:01 PM   #8
m&p45acp10+1
Senior Member
 
Join Date: May 3, 2009
Location: Central Texas
Posts: 3,310
I shoot the home cast bullets for pure economy though I will suggest trying Trail Boss for the powder. It works well, and is clean as clean gets. The largest chore for cleaning all of my guns that I shoot Trail Boss in is the carbon from bullet lube.

Oh the mold was cheap, and it works fine for me. I have pushed them to around 1300 FPS with AA#9. I keep them in the 800 to 900 FPS area with Trail Boss. No punishing recoil at all. The only time I have a problem with them is at the range when Mrs. M&P is there. Then the problem is trying to get her to put it down long enough for me to shoot it before she shoots up all of the ammo.
__________________
No matter how many times you do it and nothing happens it only takes something going wrong one time to kill you.
m&p45acp10+1 is offline  
Old December 28, 2012, 10:19 PM   #9
ForneyRider
Senior Member
 
Join Date: December 4, 2007
Location: Forney, TX
Posts: 725
H110 and various 210gr bullets with large pistol magnum primers and heavy crimp makes a very solid load.
__________________
When all is said and done, there is a lot more said than done.
ForneyRider is offline  
Old December 29, 2012, 05:02 PM   #10
magothy1
Junior Member
 
Join Date: July 4, 2012
Posts: 1
.41 loads

For me, AA #5 does real well, 10.8 gr isn't too much recoil wise. My favorite bullet is the hard to find Rem 210 JSP. The Oregon Trail 215 gr cast do well, too. Unique at 9.1 gr or so is easy to shoot. Had good luck with 2400 powder, too, at 16.2 to 17.0 gr. It's a fun caliber to shoot, enjoy.
magothy1 is offline  
Old December 30, 2012, 01:59 AM   #11
bfoosh006
Senior Member
 
Join Date: February 17, 2009
Posts: 353
Just an FYI....Blue Dot® should NOT be used in the 41 Magnum cartridge (all bullet weights).
Use of Blue Dot® in the above cases may cause a high pressure situation that could cause property damage and serious personal injury.
bfoosh006 is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 05:56 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.08119 seconds with 9 queries