The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > The Smithy

Reply
 
Thread Tools
Old December 13, 2012, 11:54 AM   #1
jkpq45
Member
 
Join Date: September 28, 2012
Posts: 44
Wildcat: .45 ACP Extra Long?

Hello All--Mods, please feel free to move the topic if I'm in the wrong sub-forum.

I'm considering a wildcat cartridge along the lines of .450 Bushmaster using a rimless, headspacing-on-the-case-mouth cartridge utilizing the wide variety of 0.450"-0.454" projectiles available for .45ACP, 45LC, .454Casull and .460S&W Magnum. I could hold pressures to the .450B limit of 38 ksi, but what's the fun in that?

I'd like to use .30-06 brass as the parent case (citing availability as the reason) vs. the .284 case the .450B is based on. I'm planning on installing this cartridge into a single-shot, break-action H&R/NEF rifle receiver to begin with.

The question is--how to fireform? I'm planning on a case OAL of ~2.25". Can I count on the extractor to "hang on" to the case hard enough that it can be prevented from being driven forward by the firing pin during forming? Any chance I can trim the case after forming?

Thanks for the advice--this is my first wildcat to headspace this way, so I appreciate the input.

jkpq45
jkpq45 is offline  
Old December 13, 2012, 07:51 PM   #2
Scorch
Senior Member
 
Join Date: February 13, 2006
Location: Washington state
Posts: 11,450
Sounds like you are talking about a rimless 45 cal version of a 444 Marlin. It can certainly be done, but it will cause you some trouble.

1- Rifles generally do not like cases that headspace on the mouth. The longer cases do not headspace well and can cause issues.

2- Rifle chambers like some taper to them to ease extraction. About .010" of taper. More later.

3- At higher pressures, recoil and bullet backout will become an issue because of the taper crimp. 45 Win Mag rifles were produced, I think they are cool, but I am not sure if they had issues with this.

4- The biggest issue is that brass cannot be made easily from 30-06, you will wind up with a rebated rim case. 45 ACP base diameter is .480" (versus .470" for 30-06/308), and that leaves the brass very thin at the case mouth (.005"-.007" in order to give the needed case taper). You are talking about higher pressure, so you need thicker brass at the case mouth, maybe .012", which will make the case mouth .475" minimum, and your base diameter is .470", so you wil be bulging the brass out to fit the chamber. Problem there, but not insurmountable.

5- For fireforming, seat a lead bullet out far enough so that it engages the lands, that will keep it from being driven forward when the firing pin hits it. Old wildcatters' trick.

Hey, have fun experimenting!
__________________
Never try to educate someone who resists knowledge at all costs.
But what do I know?
Summit Arms Services
Taylor Machine
Scorch is offline  
Old December 14, 2012, 09:10 AM   #3
HiBC
Senior Member
 
Join Date: November 13, 2006
Posts: 3,632
FWIW,the old .44 Automag was made by cutting off .308 or 30-06 brass.
HiBC is online now  
Old December 14, 2012, 11:46 AM   #4
Don H
Senior Member
 
Join Date: May 8, 2000
Location: SLC,Utah
Posts: 2,705
Sort of like the .45 Winchester Magnum that debuted in the late 1970's and chambered in the Wildey and Grizzly pistols? I think TC chambered a barrel for it at one time.
Don H is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 07:12 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.06737 seconds with 9 queries