The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > Handloading, Reloading, and Bullet Casting

Reply
 
Thread Tools
Old March 27, 2001, 09:02 PM   #1
kjm
Senior Member
 
Join Date: December 24, 1999
Location: College Station, Texas
Posts: 1,871
Since I was going to get a couple of kegs of 4895, and hi-techammo.com was selling some HPC-1 (for .45 I presume), I went ahead and ordered a keg of that too. My question is what load data would I use with this round for .40 caliber pistol loads? The guy told me that I could use Bullseye data but that HPC-1 is a tad bit slower. I suppose that means that I should ease up on the charge, but if anyone out there can give me advice I'd appreciate it. It wouldn't be difficult to figure out the .45 loads from the TM, but I'm at a loss when it comes to converting to .40-.

Thank's in advance!
kjm is offline  
Old March 28, 2001, 11:02 AM   #2
Cheapo
Senior Member
 
Join Date: November 19, 1998
Posts: 986
I'd suggest loading 10 to 30 rounds using a PUBLISHED load for Bullseye, chronographing it out of YOUR firearm, and then loading the HPC-1 to the same velocity.

Use this suggestion at your own risk. Follow all precautions in the published reloading guides. Abandon all hope at the first hints of high pressure. Compare so-called "pressure signs" to factory-new ammo using the same primer. Forget the load-to-velocity suggestion if the published reloading data for your bullet shows Bullseye with the highest reported velocity.
Cheapo is offline  
Old March 28, 2001, 01:26 PM   #3
kjm
Senior Member
 
Join Date: December 24, 1999
Location: College Station, Texas
Posts: 1,871
Great suggestions. I'll have to borrow my friends chrono, and load a few bullseye rounds. At forty dollars per 5lb keg, I could hardly pass that up. Since haz-mat has increased, I find it more economical to purchase powder in larger lots (up to four 8lb kegs) and only pay one hazmat fee. I don't do much with my pistol besides popping off balloons and the occasional rotten grapefruit or watermelon. I don't suppose accuracy is what is important in loading handgun rounds. I just wanted to find a cheap propellant that would enable me to shoot more often for much cheaper. The two handgun calibers I load are fairly common, so I might be able to figure this out. It would be a huge boon to my pocketbook if I can make it work.

As soon as I find out, I'll post back here with my results. Maybe some of y'all are into this for cheap thrills too!
kjm is offline  
Old March 30, 2001, 02:46 PM   #4
PDshooter
Senior Member
 
Join Date: March 30, 2000
Location: Illinois (PRI)
Posts: 599
Bought some Mil,surplus from High-tech.(4895) They through in a load date sheet.
PDshooter is offline  
Old March 30, 2001, 03:39 PM   #5
Southla1
Member In Memoriam
 
Join Date: March 19, 2000
Location: Jeanerette, La. Near the
Posts: 1,999
I agree with PDshooter. I bought some of the IMR4895 surplus from HiTech and they had a data sheet for all of their powders in the box.
Southla1 is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 05:15 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.06626 seconds with 9 queries