The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > Handloading, Reloading, and Bullet Casting

Reply
 
Thread Tools
Old December 7, 2012, 04:20 PM   #26
tkglazie
Senior Member
 
Join Date: December 3, 2011
Posts: 558
Thanks oldgoat. And yes, shootest, I just noticed the current SDB is carbide. Maybe older ones were not and thats what the previous poster uses. Either way, it was silly of me to use lube as a factor considering I will be using a little bit once in a while regardless, just like I do on my LCT. I find it makes things run a little more smoothly to lube a case or two in every other box or so.

The SDB really is tempting. I like the flexibility and versatility of the LnL but I already have that in my LCT. The SDB comes ready load or under $400, has the big Dillon warranty and could easily be resold if I ever decided to upgrade.

I am going to do the smart thing and stick with my decision to wait until after the holidays and decide. I spent a small fortune on guns and reloading equipment and components this year and will really need to come up with something good for the Mrs for Xmas, then worry about upping my production.
tkglazie is offline  
Old December 7, 2012, 10:33 PM   #27
Misssissippi Dave
Senior Member
 
Join Date: December 5, 2009
Posts: 1,407
Tkglazie,

This is the first time I can recall someone on this forum giving me the benefit of a doubt when I made an error. Thanks.

I pulled the dies out on the SD to double check. I stand corrected. They are carbide.

While I was at it I even put in primers and powder. It does make ammo. The powder measure is basicly the same as the one on the 550b. That powder measure works well. I loaded 50 rounds of .45 apc and the oal is just as consistant as the 550b. I'm not able to see if the primer has fed like I can on the 550b. It does take more effort to load with the SD than the 550b. I have the orginal round ball handle on both. I don't see any real reason to switch to the other handle Dillon makes for pistol ammo on the 550. I can see where that handle will help on the SD press. I also suggest the strong mount for the SD.

There are differences between the presses Dillon makes. You don't get much speed advantage with the 650 over the 550b unless you add the case feeder. Now, there is even a case feeder for the 550b. I haven't heard much about how that is working out. I think I have a little more control with the 550b operation since it only advances when I want it to. Being able to advance slowly when loading ammo the is close to a compressed load means I don't spill powder all over the place. It also makes adjusting the powder measure easier to do in my opinion.

There is a version of the 550 which is more like a turret and you can add parts to it until it becomes a full RL 550b. I'm not sure how much extra you might pay doing that way.

I have loaded well over 30k on my RL 550b over the past 12 months and probably will load close to that amount over the next 12 month. My experience with the SDB to date is limited to 50 rounds and several months just sitting on the bench waiting to get used. I'll leave it set up to load .45 large primers as I orginally planned to do with it. Yes, both of these presses have the no B.S. warrenty and that is worth a lot. A quick call and parts if needed are on the way. It takes a couple days longer if you just send an E-mail.
Misssissippi Dave is offline  
Old December 8, 2012, 10:09 AM   #28
tkglazie
Senior Member
 
Join Date: December 3, 2011
Posts: 558
No problem MD. Good contributors deserve that benefit of the doubt, especially on little things. Your knowledge has proven to be more than sound in the past.
tkglazie is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 10:36 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.06027 seconds with 9 queries