The Firing Line Forums

Go Back   The Firing Line Forums > The North Corral > Curios and Relics

Reply
 
Thread Tools
Old December 2, 2012, 10:17 AM   #1
Genepix
Senior Member
 
Join Date: April 13, 2008
Location: Sunshine State
Posts: 312
Question about Hopkins & Allen revolver

A friend showed me a gun that was passed down through the family. It is a Hopkins & Allen XL-3 .32 cal revolver that showed no serial number, but I did not take the grips off. My question is: On the right side of the frame, at the loading port, there is nothing to cover the rear of the cylinder- my old Ruger Single Six has a similar loading gate, but it is covered by a swing-out cover. The pix I've seen of the H&R appear to be the same, sans door. Also, the cylinder spins freely, and does not engage with the hammer movement. Any guess as to how much work might be required to make the gun functional? Thanks for any info.
Genepix is offline  
Old December 2, 2012, 01:29 PM   #2
James K
Staff
 
Join Date: March 17, 1999
Posts: 19,671
That gun is in the category often called "suicide specials", though the H&A guns were of better quality than most of that type. The loading port has no gate. They were made so that when the cylinder was positioned with a round under the hammer, a cartridge could not fall out. They were normally carried on half-cock; have no hammer block safety or transfer bar.

The failure of the cylinder stop indicates a broken part in the gun.

Those were inexpensive guns, selling new for $2-3. No parts are available and I doubt you could find any gunsmith to work on that gun since the cost of repairs would exceed the value of the gun. I'm afraid it is a wall hanger, but regardless, it is made for the .32 rimfire, which is very hard to get and expensive.

Jim
__________________
Jim K
James K is online now  
Old December 2, 2012, 02:34 PM   #3
Genepix
Senior Member
 
Join Date: April 13, 2008
Location: Sunshine State
Posts: 312
Thanks Jim- You're telling me what I expected to hear. I don't think anyone actually planned on shooting it, just thought I'd ask. Have a good day!
Genepix is offline  
Old December 2, 2012, 04:36 PM   #4
Mike Irwin
Staff
 
Join Date: April 13, 2000
Location: Northern Virginia
Posts: 36,074
On a lot of the older, cheaper guns of this class the cylinder would free wheel, either intentionally through design or by quick wear of the parts.

The cylinder generally was only "locked" when the hammer was cocked.
__________________
"The gift which I am sending you is called a dog, and is in fact the most precious and valuable possession of mankind" -Theodorus Gaza

Baby Jesus cries when the fat redneck doesn't have military-grade firepower.
Mike Irwin is offline  
Old December 2, 2012, 07:00 PM   #5
RJay
Senior Member
 
Join Date: November 2, 2005
Location: Arizona
Posts: 1,666
On the Hopkins and Allen, the cylinder will only lock up when the hammer is in the full cock position in single action or at a certain point when the trigger is pulled in trigger/double action. Other wise as Mike Irwin posted, it is free wheeling. These were not Colts or S&W and only sold for about $1.78 through catalogs. To recap, if the hammer is cocked and the cylinder is free spining, yes it it is broken. if the hammer is down at rest and the cylinder is free spining, no it is not broken















7a
__________________
Ron James
RJay is offline  
Old December 2, 2012, 09:23 PM   #6
James K
Staff
 
Join Date: March 17, 1999
Posts: 19,671
The gun in question, the H&A XL 3, is a spur trigger solid frame single action, not a DA break top, and IIRC the cylinder does not free wheel when the hammer is down (if the gun is working right). I will of course, stand corrected if anyone has one that works right and can check.

Jim
__________________
Jim K
James K is online now  
Old December 2, 2012, 09:49 PM   #7
Genepix
Senior Member
 
Join Date: April 13, 2008
Location: Sunshine State
Posts: 312
Thanks gentlemen!
Genepix is offline  
Old December 2, 2012, 11:05 PM   #8
RJay
Senior Member
 
Join Date: November 2, 2005
Location: Arizona
Posts: 1,666
Well, don't know Jim, Flayderman's shows something different in it's illustrations other than a spur trigger. They are labeled XL's, am I looking on the wrong page???
__________________
Ron James
RJay is offline  
Old December 3, 2012, 09:20 AM   #9
Mike Irwin
Staff
 
Join Date: April 13, 2000
Location: Northern Virginia
Posts: 36,074
IIRC H&A used the "XL" model designation liberally on a wide variety of revolvers, sort of like S&W is now doing with the once-proud Chief's Special name. It used to be a revolver. Now it's also a series of semi-autos, a rifle, a toilet plunger, a bicycle, a mechanical adding machine, etc...
This is an XL3 single action spur trigger:

http://gastatic.com/UserImages/5885/...wm_2664459.jpg

And here is an XL model double action:

http://thefiringline.com/forums/showthread.php?t=259712


XL was even used on a series of large frame revolvers chambered for cartridges like the .44-40.


So, don't get too hung up on the model designation.
__________________
"The gift which I am sending you is called a dog, and is in fact the most precious and valuable possession of mankind" -Theodorus Gaza

Baby Jesus cries when the fat redneck doesn't have military-grade firepower.

Last edited by Mike Irwin; December 3, 2012 at 05:16 PM.
Mike Irwin is offline  
Old December 3, 2012, 01:46 PM   #10
Mike Irwin
Staff
 
Join Date: April 13, 2000
Location: Northern Virginia
Posts: 36,074
Oh, and in case anyone is wondering why H&A used those letters?

My guess the answer can be found when you pronounce both of them quickly...

X.... L...

XL

Excell...
__________________
"The gift which I am sending you is called a dog, and is in fact the most precious and valuable possession of mankind" -Theodorus Gaza

Baby Jesus cries when the fat redneck doesn't have military-grade firepower.
Mike Irwin is offline  
Old December 3, 2012, 04:37 PM   #11
RJay
Senior Member
 
Join Date: November 2, 2005
Location: Arizona
Posts: 1,666
oops
__________________
Ron James
RJay is offline  
Old December 3, 2012, 05:18 PM   #12
James K
Staff
 
Join Date: March 17, 1999
Posts: 19,671
The years c. 1875-1900 were the heyday of those "suicide special" spur trigger revolvers, and H&A and others made millions of them. The makers gave the guns interesting names, but often didn't have enough pride in the product to put their own names on them.

H&A used Blue Jacket, Ranger, Dictator, Smoker, Kitemaug (?), Defender, Pioneer, Capt. Jack, Tramps Terror, Bang-Up, Czar, and probably others. Other makers used other fancy names; typing a list would take all day.

The origin of the term "suicide special" is not clear. Most folks say it indicates a cheap revolver that probably would be good only for one shot; others say it indicates the result if someone armed with one of those revolvers challenged anyone with a better gun.

Jim
__________________
Jim K
James K is online now  
Old December 5, 2012, 08:34 PM   #13
RJay
Senior Member
 
Join Date: November 2, 2005
Location: Arizona
Posts: 1,666
In view of the follow up posts in reference to the H&A, on the advise of my lawyer, disregard any thing I posted, if anyone asks, you don't know me. I don't own a computer, don't know how to use one, and I wasn't even in town that night , That's my story and I'm sticking to it. BTW, I read and was told that the term suicide special is from the 1930's and the Great Depression, hard times and the suicide rate was very high. a very inexpensive revolver that is able to fire one close shot was all that was needed, a " Suicide Special ".
__________________
Ron James
RJay is offline  
Old December 7, 2012, 10:59 PM   #14
James K
Staff
 
Join Date: March 17, 1999
Posts: 19,671
OK, as long as I can join the "you don't know me" club when I write something really dumb. (I used to own an XL 3, so I thought it was what I said.) Incidentally, the term "XL" is not in the past. It crops up from time to time, used by someone or some company that probably thinks "XL" is new and just clever as all getout.

Jim
__________________
Jim K
James K is online now  
Old December 11, 2012, 08:55 AM   #15
Magnum Wheel Man
Senior Member
 
Join Date: July 26, 2006
Location: Southern Minnesota
Posts: 8,355
so many "gun things" are thought of as new, but were 1st thought of or invented in the late 1800's, or early 1900's... I have several old Iver Johnson revolvers with a trigger type safety, similar to what the Glocks have...

that era had a huge growth of inventions & creativity...

BTW... I have a spur trigger XL, like MIKE posted, that was in like unfired condition, probably because it was in 30 rim fire... I had my machinist buddy make me a set of rifled chamber inserts, from an old 22 barrel, so the gun can be fired with 22 Colibri's ( trying to carry on that creativity )

Hopkins & Allen made some really nice guns, I hate to see them listed as "suicide specials", though as business people they also made some pretty crappy guns... however, they were one of the only "inexpensive gun producer" to regularly offer loading gates on their solid frames, folding hammer spurs, etc... & they built most all of the Merwin & Hubert guns, which were highly prizede because of their unique unloading mechanism
__________________
In life you either make dust or eat dust...
Magnum Wheel Man is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 11:32 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.08892 seconds with 9 queries