The Firing Line Forums

Go Back   The Firing Line Forums > The Hide > The Dave McCracken Memorial Shotgun Forum

Reply
 
Thread Tools
Old November 2, 2012, 08:48 AM   #1
Buzzard Bait
Senior Member
 
Join Date: June 25, 2008
Location: Republic of Texas
Posts: 333
problem with A5 Browning

Browning A5 20 gauge older gun maybe 60s vintage. This gun does not eject the last shot. Shooting skeet with it, load two rounds first shot cycles normal and loads next round which fires then that shell hangs in the port still held by the extractor and is kind of hard to get out. The gun is clean seems to be in good shape first round is fine and ejects and loads next round ok. Any ideas?
bb
Buzzard Bait is offline  
Old November 2, 2012, 02:55 PM   #2
SauerGrapes
Senior Member
 
Join Date: March 22, 2009
Location: S.E.PA.
Posts: 666
This is a shot in the dark. I've never heard of this particular problem before.

Take the butt stock off and remove the spring and clean it real well and lube sparingly. That rod and spring regulate the bolt.

You'll need to either buy a couple special screwdrivers or grind your own. If your not comfortable doing this, I suggest seeking some professional help.

I was always under the impression, Browning made the screws that way to keep people from tinkering. With the correct tools, it's not a big deal. Chances are, the gun has never been apart.
__________________
NRA member, DCF&S member, PAFOA member, USPSA member

R.I.P.____Murphy
SauerGrapes is offline  
Old November 2, 2012, 03:38 PM   #3
shortwave
Senior Member
 
Join Date: December 17, 2007
Location: SOUTHEAST, OHIO
Posts: 5,930
SauerGrapes,

I know the OP appreciates your response and will Thank You when he reads your post. I want to Thank You as well for your response and will be paying close attention to this thread as the A5 is a shotgun that I have a couple of and know very little about when it comes to diagnosing/repair issue's with them.

Too, thankfully, I've not had any issue's with either of mine.
shortwave is offline  
Old November 2, 2012, 04:49 PM   #4
jaguarxk120
Senior Member
 
Join Date: February 28, 2008
Location: Michigan
Posts: 1,931
If you go to www.midwestgunworks.com in the Browning area they have listed in pdf form the factory service manual for down load.

The manual will take you through service and disassembly steps for the Model A5.
jaguarxk120 is offline  
Old November 2, 2012, 05:45 PM   #5
Goatwhiskers
Senior Member
 
Join Date: April 8, 2009
Location: Batchelor, La.
Posts: 464
Been wrenching on Brownings longer than I like to think about. The advice about screwdrivers is spot on. The Europeans like those narrow screw slots. Get you some hollow ground driver tips and use the correct thickness and width, American taper screwdrivers WILL bugger the slots. Most Brownings suffer from lack of real maintenance due to the inherent reliability of the design and usually really need to be disassembled for a thorough cleaning--amazing how much crap can accumulate over the years. If you don't feel comfortable taking it down take it to a competent 'smith. In the interest of getting it running, the advice about the action spring is good altho they usually should be replaced along with the recoil spring. While you're at it, clean the mag tube well, lube lightly, then wipe off with a clean rag and the friction mechanism will be correctly lubricated, don't over lubricate. Make sure the friction ring is correctly installed for your loads with the gap in the outer spring matching the gap in the bronze ring. 'Bout as much as I can tell you without seeing the gun. Good luck. Goatwhiskers the Elder
Goatwhiskers is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 05:10 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.07409 seconds with 9 queries