The Firing Line Forums

Go Back   The Firing Line Forums > The Hide > The Art of the Rifle: Bolt, Lever, and Pump Action

Reply
 
Thread Tools
Old February 2, 2011, 08:12 PM   #1
oorklandboy
Member
 
Join Date: November 18, 2010
Location: Auckland, New Zealand
Posts: 15
My take on improving Howa 1500 factory trigger - in THREE parts

Pa r t 1 Howa 1500 trigger / Weatherby trigger

Being an owner from new, of the Howa 1500 Varminter Supreme in Stainless, 308 calibre, some of you already know I have had the barrel shortened by an inch and had a custom removable over-barrel suppressor fabricated. (photos to come...)

Next task was the all-discussed factory trigger.. Creep creep, you got it.. Yes, adjust this and the safety stops working... Mind you, in my days of firearm training, It was enforced that one wasnt to rely on the mechanics of a safety, but to use the semi-ready position of the bolt until actually ready to fire... Im sure this is a can of worms, so I shall not discuss this - my practices are mine alone....

I have spent a quiet public holiday pulling apart and photographing each step, in case there are other owners out there who cannot justify the costs of importing a quality aftermarket trigger, being outside the USA....
Whether right or wrong, this is what I have done to see alot of improvement in the sear surfaces... and no one anywhere it seems, has posted pics of the trigger in bits... and if nothing else, was an education...

-this has quite a few images to see, grab a coffee or beer-


1. Some of us are familiar with this, the Howa trigger group..



2. I first removed the circlip and the Safety tang retaining pin.




3. After removing the safety tang, the conical locator pin and spring are ready to fall out..



4. I then removed the rear adjusting screw completely - this frees the trigger internally from the front spring.




5. The trigger will now be loose, but captive, until the pin nearest the trigger curve is removed. i found that because earlier we had removed a circlip, the pin and other circlip can come out the other way, allowing the trigger to be removed...




6. If we look at the top of whats left , it will look like this... we want to then remove the tiny pin holding in place, the 'L' shaped sear...


Last edited by oorklandboy; February 2, 2011 at 08:51 PM. Reason: add keywords, improving google results
oorklandboy is offline  
Old February 2, 2011, 08:14 PM   #2
oorklandboy
Member
 
Join Date: November 18, 2010
Location: Auckland, New Zealand
Posts: 15
Part 2 of 3... (too many pics for one thread..)

7. Find something tiny but tough enough to drift this pin out... easy on the hammer... The wood with hole was underneath the pin, allowing the pin to come out without hitting the benchtop... This is repeated for the larger pin also... image shows larger pin half out...




8. Be wary, I was lucky enough to be on a cloth-covered workbench, and found myself looking at a random spring... it has come from deeper in the unit, being the front trigger tension spring... this had a habit of falling right out, when the trigger unit was held in the wrong way...




In between the brass fitting and the coil spring, is a hole (looking vertically into it) this is the home for the potentially loose spring. I used the same tool for removing the tiny pin to locate spring back into position.




9. After reading other articles and forums re the Howa trigger, I faced the foward part of the trigger - whether you choose to do this, is entirely up to you - though what is evident is the lack-lustre metal finish from the factory, which I wanted to tidy up while apart - also it removed a fraction of metal to potentially help with the problem of "adjust creep screw/no safety" issue. This image shows metal finish from factory...



For metal removal/polishing, I used a Spyderco Spyderco Pocket Stone (Double Stuff) ~ 303MF stone combo that I picked up while in the US a few years ago. I used the white side for sear work - they say its a 'fine', but I've never come across anything finer, and worked well without much if any metal removal - just a polish was what i wanted, and got using Inox on the stone.

oorklandboy is offline  
Old February 2, 2011, 08:15 PM   #3
oorklandboy
Member
 
Join Date: November 18, 2010
Location: Auckland, New Zealand
Posts: 15
three of 3...

10. While on the trigger, there are two sear faces to look at... see image below for reference... These two faces were cleaned up and resulted in near mirror finishes... a vast improvement on the factory finish.




11. After removing all the pins, now the "L" shaped sear will be free. Here the layout and interaction of these two parts can be seen - therefore perhaps the critical faces where 'creep' is present, and could be eliminated, hence some time was spent on these sear surfaces...
see images below...

Interaction of sears:


Sears in Battery:


Sears about to release (firing pin) [ As trigger is pulled, pivot moves trigger foward, against L sear, which then drops, allowing firing pin in bolt to come foward...]

[IMG]http://i1084.photobucket.com/albums/...ttorelease.jpg[/IMG]

Sears release, firing pin released:




12. Hence, time spent on faces of 'L' sear. I also touched up the 'back' of this, where it engages the firing pin mech, intending a cleaner 'break' as it moves down, to release the firing pin... Motion of stoning was always in same way as faces moving on each other... (not a great pic of LHS sears..)

Pin and screw in pic shows points of contact..

first image is of L sear, before work.. this surely is where alot of the creep is felt... just check the machine marks on the sears...!





For reference, as per the L sear faces, also the trigger sears cleaned up, noting that there is a small angle on the top of the trigger sear... again, perhaps critical in minimising creep where these surfaces rub...





Well, thats about all I have to offer - certainly open to comments or questions if I can help... Just reverse the process of disassembly to reassemble... watch the small trigger spring is in place, and trialed on empty chamber to then adjust screws for trigger travel and/or pull weight.
In my case, an improvement was immediate and safety still working OK...

its just a guide to the internals of the Howa manufactured trigger...

Cheers

Last edited by oorklandboy; February 2, 2011 at 11:40 PM.
oorklandboy is offline  
Old February 2, 2011, 11:00 PM   #4
viking499
Senior Member
 
Join Date: October 29, 2008
Posts: 206
Thanks for all the time and detail. I might try that after I pick up my first Howa.
viking499 is offline  
Old February 2, 2011, 11:11 PM   #5
warbirdlover
Senior Member
 
Join Date: December 13, 2009
Location: central Wisconsin
Posts: 2,324
Do ALL factory triggers come with those horrible finishes on them? No wonder the Weatherby Vanguard I tried had such a gritty feeling trigger.
warbirdlover is offline  
Old February 2, 2011, 11:24 PM   #6
oorklandboy
Member
 
Join Date: November 18, 2010
Location: Auckland, New Zealand
Posts: 15
Im guessing that , yes, this is the case from what I have read on forums that date back a fair while... that the Howa/Weatherby line of triggers arent that great.. It would be fairly easy enough for one to go online and drop in an aftermarket Jewel or Timney, as I wanted to do, but at the costs they sell here locally (NZ) and the dramas of paperwork to have these leave the US by a retailer was just too prohibtive in my case - a damn shame really.... I think at a mere glance, NZ retailers DOUBLE the costs of the US price tag.. Typically greedy...

Maybe labelled as a gift it may get here.. hah!
oorklandboy is offline  
Old February 3, 2011, 12:29 PM   #7
Kawabuggy
Senior Member
 
Join Date: April 25, 2008
Posts: 224
Looking at the trigger, I can tell you that it is either a direct copy of the Mossberg ATR100/4X4 trigger, or it IS the same trigger from those guns and Mossberg makes them for Howa.... These triggers can be easily tuned down to 1 lb. or less SAFELY if you know what you are doing with them.

They are one of the easiest triggers to work on in my experience. I only wish other manufacturers would start using this exact trigger across the board.
Kawabuggy is offline  
Old February 3, 2011, 01:10 PM   #8
oorklandboy
Member
 
Join Date: November 18, 2010
Location: Auckland, New Zealand
Posts: 15
Thanks for the info Kawabuggy Can I assume you yourself have spent some time having a play with these triggers... Im certainly keen to learn more if you're willing to share... Would you mind? If not here, then a PM..?

Mossberg aye? Hmmm, the cauldron of manufactures of these firearms/parts gets deeper!

Yes, it was fairly easy enough to figure out and work on...

If a Mossberg product, did the triggers IN the Mossbergs have a rough finish as the Howa tends to be, and require work/replacement..?
oorklandboy is offline  
Old February 3, 2011, 04:07 PM   #9
Kawabuggy
Senior Member
 
Join Date: April 25, 2008
Posts: 224
Sent you a PM with a link to a write up (with pictures) on the Mossberg trigger. Look at the pics, and you'll see how similar they are.
Kawabuggy is offline  
Old February 3, 2011, 09:13 PM   #10
oorklandboy
Member
 
Join Date: November 18, 2010
Location: Auckland, New Zealand
Posts: 15
Kawabuggy - damn fine work!! Kudos to you, and you're on the money, re the design of the triggers - got to be the same...

I read further down, and saw your addition re the later variants, re the adjusting screws.. re travel and pull...

Well done Sir... and thanks!
oorklandboy is offline  
Old February 4, 2011, 06:05 PM   #11
shanzlik
Senior Member
 
Join Date: September 28, 2009
Location: Texas
Posts: 547
Nice writeup and photos.
__________________
TSRA Life Member, NRA Endowment Life Member, SAF Life Member
My EDC - STI Shadow
My blog - firearm reviews, etc.
shanzlik is offline  
Old February 4, 2011, 07:28 PM   #12
hooligan1
Senior Member
 
Join Date: July 18, 2010
Location: Independence Missouri
Posts: 3,175
Bravo mate!!! I'm headin to the gun cabinet to get mine started!! At the same time I'm going to get on Midway USA, and order a Timney just in case I goof the process.
__________________
Thanks for coming!
hooligan1 is offline  
Old March 1, 2011, 02:28 AM   #13
oorklandboy
Member
 
Join Date: November 18, 2010
Location: Auckland, New Zealand
Posts: 15
Hooligan,

How did you get on...?
oorklandboy is offline  
Old November 1, 2012, 05:42 PM   #14
davery25
Senior Member
 
Join Date: October 4, 2011
Location: Australia
Posts: 283
Sorry, i know this thread is very old but just wondering - does this adjustment make ordering a timney trigger redundant or would a timney still be better overall?

Cheers
davery25 is offline  
Old November 1, 2012, 07:39 PM   #15
oorklandboy
Member
 
Join Date: November 18, 2010
Location: Auckland, New Zealand
Posts: 15
The only reason i perservered with this is due to the ridiculous costs that NZ retailers sell the Timney for... If a Timney is affordable for you, I'd go the Timney....

Though i DID learn a fair bit going through the process... perhaps get the timney and still have a go pulling the factory one apart...

NZ is nice, but everything is costly... very costly....
oorklandboy is offline  
Old November 1, 2012, 10:54 PM   #16
davery25
Senior Member
 
Join Date: October 4, 2011
Location: Australia
Posts: 283
You won't win sympathy from me my friend Here in Australia, everything is still expensive but i still can't have an AR-15 or M1 garand like you can.

I used to live in auckland but was too young to realise the freedom

They haven't changed the laws about semi-autos have they?
davery25 is offline  
Old November 2, 2012, 06:29 AM   #17
hooligan1
Senior Member
 
Join Date: July 18, 2010
Location: Independence Missouri
Posts: 3,175
Well it has been some time,,,, Oorklandboy I installed a Timney on mine and adjusted it down to 2.5 lbs, where it breaks like a glass rod. It lets this rifle shoot wonderfully.
__________________
Thanks for coming!
hooligan1 is offline  
Old November 2, 2012, 12:49 PM   #18
dgludwig
Senior Member
 
Join Date: February 12, 2005
Location: North central Ohio
Posts: 5,015
Very nice write-up with great photos. I found it interesting and informative. That all said, I must be one of the luckier Weatherby (Howa) Vanguard buyers because the one I bought came with an excellent trigger: light pull, smooth take-up/let-off and virtually creepless. I wouldn't change anything on it-and I'm kind of a fanatic when it comes to insisting on a good trigger, be it a rifle or a handgun.
__________________
ONLY AN ARMED PEOPLE CAN BE TRULY FREE ; ONLY AN UNARMED PEOPLE CAN EVER BE ENSLAVED
...Aristotle
NRA Benefactor Life Member
dgludwig is offline  
Old November 2, 2012, 02:30 PM   #19
Joe Chicago
Senior Member
 
Join Date: November 11, 2011
Location: Chicago area
Posts: 277
Oorkland, did you get the latest 1500 with the 3 position safety? If so, the rifle came with a twostage trigger designed to have some take-up before it broke.
Joe Chicago is offline  
Old April 28, 2013, 11:08 PM   #20
oorklandboy
Member
 
Join Date: November 18, 2010
Location: Auckland, New Zealand
Posts: 15
Davery25, if you mean we can still own, them, we can...

though anything with a flash suppressor on them, or a bayonet lug has to be removed, otherwise its classed as an MSSA, military style semi auto... bit contentious with thumbhold stocks too...

Nice work hooligan1 - what sort of groups can it shoot? Im managing 1/2 MOA with hunting and 1/4 MOA with Palma target projectiles... thats with the overbarrel suppressor on too...


Joe Chicago - now this is news to me... yes, it IS that style, with the 3 position safety... ive probably destroyed that behaviour with my fiddling, though the trigger is predictable none the less... thanks for that information though.. I dont think its well advertised as such...
oorklandboy is offline  
Old April 29, 2013, 06:39 AM   #21
hooligan1
Senior Member
 
Join Date: July 18, 2010
Location: Independence Missouri
Posts: 3,175
Hey man it's been awhile, but it shoots wonderfully, with five different loads the average is around 3/4 inch at 100 yds, some group tighter than others,.
__________________
Thanks for coming!
hooligan1 is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 05:15 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2013 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.16013 seconds with 9 queries