The Firing Line Forums

Go Back   The Firing Line Forums > Hogan's Alley > Handguns: The Revolver Forum

Reply
 
Thread Tools
Old October 29, 2012, 11:10 PM   #1
Karstark17
Junior Member
 
Join Date: October 29, 2012
Posts: 3
Need Help Fixing a Problem

Ok, I'm new to The Firing Line so hi to all. I have a problem with an old S&W .38. It was my grandfathers gun, and when he passed he left it to me. Well about 10 years ago a couple of my idiot cousins borrowed the gun from him to take shooting. They somehow got hold of some old underpowered bullets. They managed to get 3 (yes 3) bullets lodged in the barrel before they realized what was happening. They're lucky it didn't blow up in their hands. They took the gun home and put it on a drill press, and drilled out the majority of the bullets lodged in the barrel. They actually didn't mess up the barrel itself with the drill bit. You can see down the barrel now. I have no idea what kinds of rounds they were shooting, and you can't tell from looking down the barrel However, there is still quite a bit of material covering the rifling. This gun is extremely sentimental to me and I want to get it back to working order. I would really appreciate any advice.
Karstark17 is offline  
Old October 29, 2012, 11:36 PM   #2
Buzzcook
Senior Member
 
Join Date: November 29, 2007
Location: Everett, WA
Posts: 5,630
There are tools for removing lots of lead. One is called a Lewis Lead Removal Brush. There are also reamers for various calibers, they're like drill bits without burrs. Finally if you have lots of elbow grease, just use a bronse brush repeatedly.

Lots of different chemicals make the claim that they remove lead. But I'd do as much as you can mechanically first.

Foul Out is a popular treatment system. can't think of any other off thetop of my head.
Buzzcook is offline  
Old October 30, 2012, 07:58 AM   #3
cecILL
Senior Member
 
Join Date: August 13, 2001
Location: central IL
Posts: 488
Mercury dissolves lead.
cecILL is offline  
Old October 30, 2012, 08:26 AM   #4
Bob Wright
Senior Member
 
Join Date: July 10, 2012
Location: Memphis, Tennessee
Posts: 1,897
I have used a steel rod of near bore diameter, wrapped in plastic tape, and driven bullets out using a mallet to drive the rod through the barrel.

Bob Wright
Bob Wright is offline  
Old October 30, 2012, 08:46 AM   #5
moxie
Senior Member
 
Join Date: October 17, 2006
Location: TX
Posts: 513
cecILL,

Your post that mercury dissolves lead was very helpful. Thanks so much.
__________________
If you want to shoot...shoot...don't talk! Tuco

USAF Munitions 1969-1992
RVN 1972-1973
moxie is offline  
Old October 30, 2012, 11:15 AM   #6
MrBorland
Senior Member
 
Join Date: May 31, 2007
Location: NC
Posts: 1,855
A brass .38 cal squib rod would be best.

Yes, mercury is supposed to dissolve lead, but I wouldn't mess with the stuff myself. A non-toxic 50/50 mix of vinegar and peroxide will dissolve lead. I don't think it's meant to dissolve drilled-out bullets, but to clean residual traces from a leaded barrel. Prolonged exposure may also attack steel, so I'd try the squib rod first, or at least, as Bob suggested, a steel rod well-wrapped in plastic tape.

BTW, any indication the barrel's bulged?
MrBorland is offline  
Old October 30, 2012, 11:35 AM   #7
Clifford L. Hughes
Senior Member
 
Join Date: February 24, 2011
Location: Southern Californis
Posts: 795
Mercury iis an extreamly poisonous subsistence. Don't use it. Our water ways and are fish are already contaminated with mercury. We don't need more contamination.


Semper Fi.


Gunnery Sergeant
Clifford L. Hughes
USMC Retired

Last edited by Clifford L. Hughes; October 30, 2012 at 11:36 AM. Reason: spelling
Clifford L. Hughes is offline  
Old October 30, 2012, 11:40 AM   #8
parsonbw
Junior Member
 
Join Date: August 5, 2010
Posts: 2
Take a dowel of slightly smaller than the barrel, obtainable at any local hardware, and drive the lead out from the front of the barrel. Be careful not to hit the rebound. You should be good to go with patience and a good hammer.
parsonbw is offline  
Old October 30, 2012, 11:40 AM   #9
kraigwy
Senior Member
 
Join Date: June 16, 2008
Location: Wyoming
Posts: 9,475
You'll be money a head if you take it to a qualified gun smith.
__________________
Kraig Stuart
CPT USAR Ret
USAMU Sniper School Oct '78
Distinguished Rifle Badge 1071
kraigwy is offline  
Old October 30, 2012, 11:55 AM   #10
willr
Senior Member
 
Join Date: July 23, 2006
Posts: 237
Take it to a good gunsmith! However, if you ever try to drive a stuck bullet out of a revolver, be sure that you fill the barrel up with clp or some very good penetrating oil beforehand. I have had a couple of squib rounds which stuck bullets in the barrel. Attemps to drive them out were not successful until I used some clp. The bullets then drove very easily and with no damage.

willr
willr is offline  
Old October 30, 2012, 10:18 PM   #11
Karstark17
Junior Member
 
Join Date: October 29, 2012
Posts: 3
Thanks for all the advice.
Karstark17 is offline  
Old October 30, 2012, 10:22 PM   #12
MLeake
Senior Member
 
Join Date: November 15, 2007
Location: Outside KC, MO
Posts: 10,128
Dowels may be commonly used, but may not be a good idea. I've been told that when they splinter, it's not fun trying to get all the little pieces of wood out of the rifling.
MLeake is offline  
Old October 30, 2012, 10:23 PM   #13
Karstark17
Junior Member
 
Join Date: October 29, 2012
Posts: 3
Thanks for the tip on the Lewis Lead Removal Brush Buzzcook. I read some reviews online and decided to order one. It seems like it will solve the problem. Well see when it gets here.
Karstark17 is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 03:53 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.09971 seconds with 9 queries