The Firing Line Forums

Go Back   The Firing Line Forums > The Hide > The Dave McCracken Memorial Shotgun Forum

Reply
 
Thread Tools
Old October 24, 2012, 01:54 AM   #1
bamaranger
Senior Member
 
Join Date: October 9, 2009
Location: North Alabama
Posts: 4,267
Win. Model 12 ?

Ok pump gun fans, here ya go.

Did Winchester produce the Model 12 in 16 gauge with 26" bbl and full choke?

There is one for sale locally so configured. I suspect it's been cut. The muzzle bears a shiny ring and is not blued, and 26" - full does not seem right for that era.

Who knows?
bamaranger is offline  
Old October 24, 2012, 07:33 AM   #2
gunut
Member
 
Join Date: March 12, 2011
Location: Sussex Wi.
Posts: 23
yes they did.....right from the start until the late 40s or early 50s when they started cutting back on barrel/choke combinations.....measure the choke....on winchesters the standard drop in choke gauge works pretty good...
gunut is offline  
Old October 24, 2012, 12:47 PM   #3
BigJimP
Senior Member
 
Join Date: February 23, 2005
Posts: 11,221
Measure the inside of the bore --- past the chamber - mid barrel if you can ...and then measure the inside of the bore at the choke end ....to make sure there still is a "choke" to the barrel.

If its been cut ....there probably will not be a "choke" to the barrel...or it might have been fit for a Cutts Compensator at some point / they were very common back in the day.

You can't just go by what the barrel says...
BigJimP is offline  
Old October 25, 2012, 10:28 AM   #4
BLUETIP
Senior Member
 
Join Date: September 30, 2012
Location: tennessee
Posts: 119
Yes, what bigjim said
BLUETIP is offline  
Old October 28, 2012, 07:52 AM   #5
old roper
Senior Member
 
Join Date: June 11, 2007
Posts: 1,053
It could be cut back as they made 28" pretty common

http://www.gunsinternational.com/Win...n_id=100289069
__________________
Semper Fi
Vietnam
VFW
old roper is offline  
Old October 28, 2012, 08:37 AM   #6
jaguarxk120
Senior Member
 
Join Date: February 28, 2008
Location: Michigan
Posts: 1,928
The shiny ring could be the solder left behind from a Cutts/Poly choke that was removed.

Those chokes are very good but don't add anything to the value. Actually they take away from the value. So a gun with out it would have a higher asking price than with it.
jaguarxk120 is offline  
Old October 28, 2012, 02:23 PM   #7
SOUTHERN WOODS
Member
 
Join Date: October 24, 2012
Posts: 16
If this is like the M97's check to see if the serial number on the receiver and the barrel match.

Winchester may have phased out with putting a serial number on both (I'm too lazy to check my reference book ) but it could very well be a take off barrel from another gun that was either cut or standard length.
SOUTHERN WOODS is offline  
Old October 28, 2012, 04:55 PM   #8
old roper
Senior Member
 
Join Date: June 11, 2007
Posts: 1,053
I had to go pull my model 12 16ga and see what the barrel length was it's 28" full choke and has a rib serial # 91XXXX and was made 1942.

I also have model 12 20ga with rib and choke is CYL serial # 64XXXX made 1931.
__________________
Semper Fi
Vietnam
VFW
old roper is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 07:25 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.07041 seconds with 9 queries