The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > Handloading, Reloading, and Bullet Casting

Reply
 
Thread Tools
Old October 25, 2012, 05:18 AM   #1
UncleGrumpy
Member
 
Join Date: March 10, 2012
Posts: 32
Fire Forming in a Martini action

Hi,

I just fire formed a box of .22 Hornets into the K-Hornet in a re-barrelled bsa martini for the 1st time ever.

I have noticed that the cases width expanded only on one side. It is quite prominent just forward of the cases head.

With my limited knowledge, I am guessing the case is not being centered when loaded and is laying on one side of the receiver. My next assumption is that the case has now been overstretched on the one side and is a prime suspect for early head separation.

Can anyone shed some light on this.

cheers
UncleGrumpy is offline  
Old October 25, 2012, 06:56 AM   #2
Goatwhiskers
Senior Member
 
Join Date: April 8, 2009
Location: Batchelor, La.
Posts: 461
Some pics would be very helpful. If your cases are stretched only on one side you have a severely mis-shapen chamber, unknown cause, and you're due for a re-barrel job. GW
Goatwhiskers is offline  
Old October 25, 2012, 08:24 AM   #3
PetahW
Senior Member
 
Join Date: September 19, 2008
Posts: 4,679
AFAIK, the only difference between a standard Hornet and a K-Hornet is in the blown out shoulder area, so if your case is expanded near the head/rim, as if it fired while lying in the bottom of an oversized chamber, it most likely was...............

I would think something's up with the chamber proper, to make it larger than a standard Hornet chamber, allowing the expansion, or the cases were excessively sized down prior to the fireforming (which could amount to the same thing, relatively).


.
PetahW is offline  
Old October 25, 2012, 07:01 PM   #4
UncleGrumpy
Member
 
Join Date: March 10, 2012
Posts: 32
hi,

Goatwhisker, I tried to photo it yesterday but it didn't come out any good. I'll try again using another camera.

PetahW, the cases fire formed were brand new Winchester hornet. The neck appears to have formed ok.
UncleGrumpy is offline  
Old October 26, 2012, 08:43 AM   #5
Unclenick
Staff
 
Join Date: March 4, 2005
Location: Ohio
Posts: 10,195
I think this thread belongs in handloading, as there isn't necessarily a gunsmithing issue involved, so I'll move it for you.

Winchester sometimes has pretty awful wall thickness variability and the thin side will expand more than the thick side; what the late Roger Johnston called a banana shaped case from the slight longitudinal curvature that often also results. Unless you get a NECO gauge or the RCBS Case Master, both of which use the chord anvil Roger Johnston designed for the NECO gauge originally (I think the patent expired, which is why RCBS now has it), I don't know a good way to see wall thickness runout back near the case head. But that's what you want to measure.

Unless you know your chamber is oval, the brass wall thickness seems like the most likely critter.
__________________
Gunsite Orange Hat Family Member
CMP Certified GSM Master Instructor
NRA Certified Rifle Instructor
NRA Patron Member
Unclenick is offline  
Reply

Tags
martini k hornet

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 02:14 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.07870 seconds with 9 queries