The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > Handloading, Reloading, and Bullet Casting

Reply
 
Thread Tools
Old October 9, 2012, 02:22 PM   #1
rajbcpa
Senior Member
 
Join Date: August 27, 2012
Posts: 315
Hornady L-N-L pawl adjustment for indexing

This press is new - I have had it about 6 weeks or so.

Anyway, on the downstroke, the press indexing often does not go far enough to the right (clockwise movement) so that detent ball in the shellholder clincks into place.

This is somewhat inconsistent. When the arm is released quickly, the indexing usually works well and most of the problem appears to ocurr during a slower release of the ram arm.

During the first week, I busted two pawls, so I'm more careful now if anything starts to jam.

According to Hornady Customer Service, "the starting point for the adjustement is to screw each indexing pawl down 100% and back it out 1.5 turns. If any additional adjustment is needed, move the pawl adjustment screw by 1/16th turn."

I have adjusted both pawls by more than 1/2 turn and the indexing on the downstroke does not appear to advance any further.

Question: Does the right pawl or left pawl adjust the indexing on the downstroke? Do I need to crank the pawl adjustment screw more, say 1 or 2 full turns?

Thx..
rajbcpa is offline  
Old October 9, 2012, 03:06 PM   #2
LE-28
Senior Member
 
Join Date: September 24, 2012
Location: North Carolina
Posts: 380
The left pawl runs the downstroke, Adjust them both like Hornady said to do, On the up stroke the shell plate should also click into the detent, then you can adjust the left pawl up a little to make it advance a little further on the down stroke.

Adjust it no more than a eighth of a turn until it just clicks in and that's all.

I had to advanse mine a little when it was new because I run the cycle slower then it was apparently designed to be ran.

Mine works fine this way, even if I get going to fast.
LE-28 is offline  
Old October 11, 2012, 11:27 PM   #3
TheTinMan
Senior Member
 
Join Date: December 8, 2008
Posts: 102
My advice is to watch the way the machine works, operating the handle slowly. Adjust only one pawl at a time and make tiny adjustments until you just get the shellplate to click into place.

Did you grease the ball bearings? REM DriLube or equivalent on bearing surface underneath?
TheTinMan is offline  
Old October 12, 2012, 09:36 PM   #4
Valerko
Senior Member
 
Join Date: April 28, 2012
Location: NY
Posts: 154
How is that LNL ,anyway?
Been thinking about getting one. Mostly for pistol ammo.
Valerko is offline  
Old October 18, 2012, 09:18 AM   #5
cryogenic419
Senior Member
 
Join Date: March 29, 2009
Location: NW Ohio
Posts: 430
This thread has been most helpful when it comes to adjusting the pawls.



http://thefiringline.com/forums/showthread.php?t=368171
cryogenic419 is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 04:16 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.06091 seconds with 9 queries