The Firing Line Forums

Go Back   The Firing Line Forums > Hogan's Alley > Handguns: The Revolver Forum

Reply
 
Thread Tools
Old October 5, 2012, 04:32 AM   #1
AraneaeFatalis
Member
 
Join Date: January 24, 2008
Posts: 51
"Old West" Finish on a Stainless Steel New Vaquero?

Is it possible? I've seen the glass bead blasted that's been done on stainless steel guns, but while looking at Uberti's website they have an Old West finish that makes the gun look, well, old.. Any way to get this replicated on my Stainless Steel New Vaquero? Been searching around the internet, but haven't found anything really.
AraneaeFatalis is offline  
Old October 5, 2012, 04:57 AM   #2
Shadi Khalil
Senior Member
 
Join Date: September 23, 2006
Location: Alexandria, VA
Posts: 4,987
You must be talking about case hardening on a blued revolver. You could have your revolver blued, then case hardened but it might cost more than your expecting, depending on who does it.
Shadi Khalil is offline  
Old October 5, 2012, 05:05 AM   #3
AraneaeFatalis
Member
 
Join Date: January 24, 2008
Posts: 51
It's not blued that I saw. It's a satin steel look that has some 'wear' look to it. Here's a picture:
AraneaeFatalis is offline  
Old October 5, 2012, 05:29 AM   #4
MJN77
Senior Member
 
Join Date: April 27, 2009
Location: on a hill in West Virginia
Posts: 710
That "old west" finish is the absence of a finish. It is bare gunmetal basically. So, no you cannot do that to a stainless revolver. It would have to be done to a blued revolver.
MJN77 is offline  
Old October 5, 2012, 09:38 AM   #5
Bill DeShivs
Senior Member
 
Join Date: April 7, 2006
Posts: 7,219
"Worn" revolvers were new at one time!
Yours can be bead blasted and scuffed up.
__________________
Bill DeShivs
www.billdeshivs.com
Bill DeShivs is offline  
Old October 5, 2012, 12:19 PM   #6
gak
Senior Member
 
Join Date: February 28, 2005
Location: Aridzona
Posts: 2,767
As others have said, best you can do is bead blast and scuff up. I have two - a Cimarron (Uberti) and USFA Rodeo - done up after the fact. But, as said, they had originally been blued. The Cimarron was actually done for me by the smith at Cimarron on this side of the pond as they didn't have any of the "Original" (old west) finish in my caliber (.44 Sp) in their shipment order at the time and I was impatient. Through my LGS that was friendly with them, they offered to "do" a blued Model P they were inspecting on the bench. The USFA I had done by my smith.
Cimarron top, USFA bottom, 4th (late 3rd( Gen Colt in the middle.

Another of the Cimarron

Back to the stainless, there may be some "acid etching" I'm not aware of, but I say no, don't go there. I'd get a blue'd one to 'speriment with (there are formulas in threads in several of these forums, often involving vinegar, sometimes naval jelly to strip, etc.)

About Rugers, it's my understanding the underlying "in the white" steel on blued guns is brighter than other brands, this according to my smith, so results may be different. Not sure I've seen a blued Ruger "antiqued." Would be interesting. The current (New Vaquero) crop is nothing special to look at with it's plain blue (black) finish, so it's tempting to mess with. I'll post if I get the itch!

Last edited by gak; October 5, 2012 at 12:27 PM.
gak is offline  
Old October 19, 2012, 12:58 PM   #7
dgludwig
Senior Member
 
Join Date: February 12, 2005
Location: North central Ohio
Posts: 5,182
Quote:
while looking at Uberti's website they have an Old West finish that makes the gun look, well, old..
I guess I've never understood the rationale behind buying new "old" guns, anymore than I've ever grasped the idea of paying for new jeans that are already half-worn out. My take on it is that if I want a gun that looks old, I'll be the one who does the aging...but that's just me.
__________________
ONLY AN ARMED PEOPLE CAN BE TRULY FREE ; ONLY AN UNARMED PEOPLE CAN EVER BE ENSLAVED
...Aristotle
NRA Benefactor Life Member

Last edited by dgludwig; October 22, 2012 at 02:20 PM.
dgludwig is offline  
Old October 19, 2012, 03:51 PM   #8
Deja vu
Senior Member
 
Join Date: March 14, 2010
Location: Border of Idaho & Montana
Posts: 2,183
Perhaps the OP is talking Case-Hardened?

The Uberti has beautiful case hardened guns on there web page.

if that is the case I think it is possible to do on a stainless bu it will be more work for the person applying it and thus more money.
__________________
Shot placement is everything! I would rather take a round of 50BMG to the foot than a 22short to the base of the skull.

all 25 of my guns are 45/70 govt, 357 mag, 22 or 12 ga... I believe in keeping it simple
Deja vu is offline  
Old October 19, 2012, 08:40 PM   #9
DPris
Senior Member
 
Join Date: August 19, 2004
Posts: 4,800
You can't "blue" a stainless Ruger & then case-harden it.
Denis
DPris is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 08:20 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.08979 seconds with 9 queries