The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > The Smithy

Reply
 
Thread Tools
Old September 16, 2012, 12:14 PM   #1
rich s
Junior Member
 
Join Date: September 16, 2012
Posts: 11
vz24 conversion

I would like to convert a mauser vz24
I was hoping to re-barrel with 30-06 but see that they are too long for the magazine.
What cartridge, readily available with a range of bullet sizes will feed properly without magazine alterations
rich s is offline  
Old September 16, 2012, 01:13 PM   #2
James K
Staff
 
Join Date: March 17, 1999
Posts: 19,521
The VZ-24, or any standard length 98 Mauser action, can be reworked to .30-'06 by grinding out some on the ends of the magazine box and feed ramp. It was done to hundreds of thousands of WWII "bringback" Mausers with no problems. It does limit the rifle in that long seated bullets cannot be used, but standard (SAAMI spec) length rounds will work OK.

A small amount of work on the cartridge guides on the bottom of the rails might be needed, but that is no problem.

Jim
__________________
Jim K
James K is offline  
Old September 16, 2012, 05:30 PM   #3
firewrench044
Senior Member
 
Join Date: July 9, 2007
Location: Fort Pierce, Florida
Posts: 191
308
I have rebarreled many Mausers into 308 (several were VZ24s )

Wilson makes a very good barrel
short chambered, 1/10 twist, 24" length
available from Brownells
firewrench044 is offline  
Old September 16, 2012, 07:42 PM   #4
wyop
Senior Member
 
Join Date: July 15, 2012
Location: Wonderful, Windy Wyoming
Posts: 133
The VZ24 will take a '06 with a little grinding and filing. It's not that difficult.
wyop is offline  
Old September 16, 2012, 10:50 PM   #5
James K
Staff
 
Join Date: March 17, 1999
Posts: 19,521
Conversion to .308 is a lot easier, but that is not what Rich asked.

JIm
__________________
Jim K
James K is offline  
Old September 27, 2012, 05:01 PM   #6
Clark
Senior Member
 
Join Date: December 4, 1999
Location: WA, the ever blue state
Posts: 2,995
Getting 30-06 to feed from a VZ24 is a small task compared to welding the bolt and drilling and tapping the receiver, provided one buys an after market magazine box.

i have milled out magazine boxes, and I have bought them, and buying is better.

http://www.brownells.com/.aspx/pid=9...ARD-FLOORPLATE

To me, Mauser sporterizing is clear in the Walsh book with specific dimensions to change the magazine box and feed lips, it is scatter brained in the Kuhnhausen book. I have been sporterizing Mausers for 47 years and will do another one in a week.
__________________
The word 'forum" does not mean "not criticizing books."
"Ad hominem fallacy" is not the same as point by point criticism of books. If you bought the book, and believe it all, it may FEEL like an ad hominem attack, but you might strive to accept other points of view may exist.
Are we a nation of competing ideas, or a nation of forced conformity of thought?
Clark is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 09:43 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.06752 seconds with 9 queries