The Firing Line Forums

Go Back   The Firing Line Forums > Hogan's Alley > Handguns: The Semi-automatic Forum

Reply
 
Thread Tools
Old August 13, 2012, 11:55 AM   #26
jasmith85
Senior Member
 
Join Date: April 6, 2012
Location: Tennessee
Posts: 368
I had no problems putting a couple hundred rounds through my 1911. It seems to ricochet more than other brands but that was probably just bad luck.
jasmith85 is offline  
Old August 13, 2012, 12:45 PM   #27
AeroEngineer
Member
 
Join Date: November 9, 2011
Location: Northern Virginia
Posts: 24
I've put multiple hundreds of rounds through my CZ clone (Jericho 941) without an issue. As reliable and accurate as any other plinking/training ammo I've used.
AeroEngineer is offline  
Old August 13, 2012, 01:07 PM   #28
Brian48
Senior Member
 
Join Date: December 21, 2001
Location: Boston, People's Republic of MA
Posts: 1,371
Been using Blazer for years in 9mm and 45acp. Great stuff, good performance, and in my opinion, excellent quality. My only complaint is that the cost difference between it and it's brass counterparts are not that great any more, making it less of a value buy than a few years ago.
__________________
Proud to have served.
Brian48 is offline  
Old August 13, 2012, 02:46 PM   #29
drail
Junior member
 
Join Date: February 2, 2008
Posts: 3,150
Just make sure you get ALL of the fouling off of the chamber walls. The finish on the alum. cases tend to stick to dirty chambers.
drail is offline  
Old August 13, 2012, 05:11 PM   #30
Erikbal
Senior Member
 
Join Date: January 12, 2012
Location: Olean, NY
Posts: 374
I've ran it through my S&W Bodyguard 380 and my Ruger SR9C with no problems at all. As a matter of fact I've never had a misfire or any type of failure ever with either gun.
__________________
S&W Bodyguard 380
Ruger SR9C
Erikbal is offline  
Old August 13, 2012, 08:06 PM   #31
Straightshooter629
Senior Member
 
Join Date: August 30, 2009
Location: Columbus, Ohio
Posts: 475
No problems in my .40 or 9mm's. The only problem I have with Blazer Alu. is in my .357 revolver. It seems the cases swell and are hard to eject. Never have a problem with brass cases.
Straightshooter629 is offline  
Old August 13, 2012, 10:24 PM   #32
CDR_Glock
Senior Member
 
Join Date: September 30, 2010
Posts: 123
No problems in 1911s, my Glocks or Springfield XDM.
CDR_Glock is offline  
Old August 13, 2012, 10:36 PM   #33
jfrey
Senior Member
 
Join Date: May 16, 2008
Location: Coastal South Texas
Posts: 553
Will not feed in any of my Brileys but my G36 loves it. Works well in all my Hi-Powers and Glocks. Haven't tried it in my Shield yet.
jfrey is offline  
Old August 15, 2012, 01:18 AM   #34
JJW
Member
 
Join Date: March 3, 2012
Location: Dayton, Ohio
Posts: 59
I have used Blazer aluminum in both my .380 and 9mm with 0 problems. However, nothing but feed problems in .22 cal in my Beretta, Mark III, and Remington 22-A.
__________________
"The philosophy of gun control: Teenagers are roaring through town at 90MPH, where the speed limit is 25. Your solution is to lower the speed limit to 20."
- Sam Cohen (inventor of the neutron bomb)
JJW is offline  
Old August 15, 2012, 01:22 AM   #35
gyvel
Senior Member
 
Join Date: August 30, 2009
Location: Northern AZ
Posts: 5,229
My only experience with Blazer has been with 9mm Largo, but it ran flawlessly through my Astra 400 and Bergmann-Bayard.
gyvel is offline  
Old August 15, 2012, 06:44 AM   #36
akguy1985
Senior Member
 
Join Date: May 17, 2012
Location: Claremore, Oklahoma
Posts: 179
I've never had any issues with it whatsoever.
__________________
Marksman of the mezzanine
akguy1985 is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 08:26 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.08201 seconds with 9 queries