The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > The Smithy

Reply
 
Thread Tools
Old June 19, 2012, 01:35 AM   #1
UncleGrumpy
Member
 
Join Date: March 10, 2012
Posts: 35
Maths: M17 + Scope = BIG Problem

Hi,

In the late 60's my dad turned a M17 into a .243 which turned into a damn fine rifle. It was fitted back then with a scope mount and a 7x36mm Kahles. As his age is gaining on him, a new scope was decided to go on. He is sold on fitting a Bushnell ?-16x50mm

So now I find the problem. The mount maker is no longer. No modern twist turn rings fit the base. I was told that the existing mount would have been custom fitted and drilled because of something to do with removing the original rear sight. The existing screw holes do not line up with current mounts sold as M17 mounts.

So I have come to three possible answers,
1) weld up the existing screw holes and try to find and fit a new mount kit. 2) Make some form of bushing to lift the bridge up off the rifle, so the existing rings will be at the right height.
3) Give up!

What do I do?

Cheers
UncleGrumpy is offline  
Old June 19, 2012, 07:23 AM   #2
Doyle
Senior Member
 
Join Date: June 20, 2007
Location: Starkville, MS
Posts: 5,085
The existing screw holes can be filled without welding. In involves turning a screw into them and using a ball peen hammer to peen the screw metal into the receiver. The excess is then filed off and a touch of bluing applied. If done properly, it will take a serious magnifying glass to find where the hole was. I would advise doing that and then retapping for a modern scope base.
Doyle is online now  
Old June 19, 2012, 08:30 AM   #3
HiBC
Senior Member
 
Join Date: November 13, 2006
Posts: 3,816
There was more than one way to do it,but one practice was to shape the rear bridge to match a Remington,and drill and tap to take a Redfield Rem base.

There are a lot of old Redfield rings and bases squirreled away in old gun shops,etc.

Might be if you check into that you will get lucky.

What may be less trouble than welding/filling/redrilling the receiver would be to look at Weaver type base blank stock or modifying another
base a little bit.

I'd rather mess up and start over on the base.

Last edited by HiBC; June 19, 2012 at 08:37 AM.
HiBC is offline  
Old June 19, 2012, 08:56 AM   #4
UncleGrumpy
Member
 
Join Date: March 10, 2012
Posts: 35
Hi, After reading the two above answers, I thought of another possible option.

Would it be easier to find a new base similar in shape and attach it to the top of the existing base.

Do you think this would work?
UncleGrumpy is offline  
Old June 19, 2012, 12:16 PM   #5
velocette
Senior Member
 
Join Date: May 25, 2007
Location: South Florida
Posts: 846
Sporterized '17 Enfields could use mounts made for the Remington model 30 rifle. The Rem m30 is and was a civilian model of the '17 Enfield. The rear sight "ears" were removed & the area rounded. That would be a good place to start. Brownells stocks the Weaver mounts, (#11). Depending upon how much the rear of the receiver has been modified / rounded, you may need to shim the front or the rear to gain proper scope leveling.
It took me several trys to get my '17 Enfield on paper.

Roger

__________________
Trigger control + Breath control + Sight alignment = Gun Control.
http://www.hrpclub.info/
NRA Smallbore Prone Master
velocette is offline  
Old June 19, 2012, 07:05 PM   #6
HiBC
Senior Member
 
Join Date: November 13, 2006
Posts: 3,816
Velocette gave you some good info,and even a Rem 700 one piece long action base may be just right,or easy to mod.Some of those only have 2 screws fwd and one rear.

Some folks would just get her done,but many would try to set up to some standard part when they can.

I do not think saddling base on top of base would be a good path,

If a piece Weaver rail will suit you,see if Farrell can help you.Call them.

I don't have a number or even know if they are still in business.You get to dig!
HiBC is offline  
Old June 19, 2012, 10:43 PM   #7
langenc
Senior Member
 
Join Date: August 19, 2007
Location: Montmorency Co, MI
Posts: 1,187
This gentleman gives good info. Dont look to be a big problem. Welding==NO.
langenc is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 05:58 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.07603 seconds with 9 queries