The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > Handloading, Reloading, and Bullet Casting

Reply
 
Thread Tools
Old May 17, 2012, 12:59 PM   #1
tmorone
Senior Member
 
Join Date: October 22, 2010
Posts: 221
Loading .223 on an XL650 (or any progressive)

Hi everyone,

So I've been loading various pistol cartridges for quite a while and have finally decided to step into doing .223 and maybe .308 later on down the road but I'm concerned about one step.

I've got a Dillon XL650 and a RCBS Turret press, so I'd like to use the Dillon since it's super fast...but... case trimming is where I get hung up.

Do any of you load .223 (for AR's) on an XL650 and how do you trim the brass? Since once it hits the size deprime station on the progressive press the newly sized brass is immediately primed on the downstroke. My only thought is to deprime and size the brass on the turret press, then trim it, then just move on over to the Dillon for priming/powder/seating.

Really hope I'm making a mountain out of a molehill- what do you all do?
tmorone is offline  
Old May 17, 2012, 02:11 PM   #2
eldorendo
Senior Member
 
Join Date: May 8, 2012
Posts: 224
I use the RCBS X die, which generally prevents the need to trim, after the initial trim.
eldorendo is offline  
Old May 17, 2012, 03:36 PM   #3
snuffy
Senior Member
 
Join Date: May 20, 2001
Location: Oshkosh wi.
Posts: 2,757
I only load .223 on my 650 that DON'T need to be trimmed. That means sorting the cases before loading, then only loading those that can be loaded WITHOUT being trimmed.

Those that DO need trimming, get sized in a single stage, then trimmed. Loading those, I eliminate the size die, or back it way out so it only passes the sizer button into the case a bit.

Sent by hammer and chisel on a stone tablet!
__________________
The more people I meet, the more I love my dog

They're going to get their butts kicked over there this election. How come people can't spell and use words correctly?
snuffy is offline  
Old May 17, 2012, 06:57 PM   #4
tmorone
Senior Member
 
Join Date: October 22, 2010
Posts: 221
Thanks for the info guys. I'd never heard of that RCBS die until today but it sounds like a good option.

I'm thinking I'll just resize them on the turret press, trim if necessary, then store them until I have enough to make it worth setting up the Dillon.

Thanks again!
tmorone is offline  
Old May 17, 2012, 07:03 PM   #5
CherokeeT
Senior Member
 
Join Date: April 23, 2008
Location: Medina, Ohio
Posts: 263
I do all the case prep on single stage, trim separately with a Giraud, then go to the progressive.
__________________
God Bless America
US Army, NRA Endowment
TSRA Life, SASS
CherokeeT is offline  
Old May 17, 2012, 09:20 PM   #6
zippy13
Senior Member
 
Join Date: August 23, 2008
Location: SoCal
Posts: 6,391
Like the others, with .223s I trim and prep separately.
zippy13 is offline  
Old May 17, 2012, 10:53 PM   #7
Eazmo
Senior Member
 
Join Date: April 15, 2011
Location: Arizona
Posts: 164
Quote:
Like the others, with .223s I trim and prep separately.
Yuppers same here!
__________________
I'm just an average man
I drive a average van
My dog ain't got no pedigree!
Eazmo is offline  
Old May 17, 2012, 11:36 PM   #8
Vance
Senior Member
 
Join Date: January 16, 2011
Location: North Bend, OR
Posts: 462
I am going to use the RCBS X-Die. All this sizing and trimming on a different press first is for the birds.
Vance is offline  
Old May 18, 2012, 06:35 AM   #9
Edward429451
Junior member
 
Join Date: November 12, 2000
Location: Colorado Springs, Colorado
Posts: 9,494
De-priming throws trash all over the place, so I do depriming and other brass prep on a single stage and then load it on my 550B. No trash, no sticky cases or anything not sparkly clean goes into the Dillon.
Edward429451 is offline  
Old May 18, 2012, 08:32 AM   #10
jmorris
Senior Member
 
Join Date: November 22, 2006
Posts: 1,560
I load 223 on a 650 and a 1050. Size/deprime and trim on the 650 and load on the 1050.



jmorris is offline  
Old May 19, 2012, 07:52 AM   #11
Jimro
Senior Member
 
Join Date: October 18, 2006
Posts: 5,437
I resize a batch, then trim a batch to min length (just got a possom hollow trimmer that really speeds up the trimming part). By trimming to min I expect to get my 4 reloads from the brass without need to resize and trim as separate operations again.

Jimro
__________________
"Gorsh" said Goofy as secondary explosions racked the beaten zone, "Did I do that?"

http://randomthoughtsandguns.blogspot.com/
Jimro is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 07:02 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.08565 seconds with 9 queries