The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > The Smithy

Reply
 
Thread Tools
Old April 29, 2012, 04:20 PM   #1
Slowhand
Senior Member
 
Join Date: July 9, 2010
Location: Irmo, SC
Posts: 262
Leinad Cobray FMJ Model DD 45/410 Derringer



This is a Leinad –Cobray-FMJ .45 Long Colt/.410 Derringer. It’s 7” in total length, with a 3 3/4” Double Barreled length. She’ll also fire a .410 gauge, 3” shotgun round. She’s marked as being made by Leinad Inc. in Ducktown, Tennessee. Model DD CAL 45. You’ll have to excuse the name but there’s loads of history behind this little beast. Which I have done loads of research on.

You press the Safety Bar Pin to safe, slide the barrel release and break the barrel down to reload. On top the hammer is a two position switch that selects which barrel is fired. The Safety Bar Pin and the Safety E Clip have seen better days. I ordered a replacement from Practical Tactical up in Louisville, Ky. He has parts available for this thing. The game plan is to replace the Bar Pin and E Clip.


http://www.homegunsmith.com/cgi-bin/...structions.pdf

I’ve down loaded the assembly instructions from Home gunsmith. Has anyone had any experience with one of these?
Slowhand is offline  
Old April 30, 2012, 11:11 PM   #2
Slowhand
Senior Member
 
Join Date: July 9, 2010
Location: Irmo, SC
Posts: 262
Repair work done...



I got the parts from Tactical Practical this afternoon via the US Mail and gave them a thank you call. They sent a replacement Leinad Safety Bar/pin plus 4 of the Safety Clips.

I rounded up the tools I’d need. A non-marring hammer, some plastic punch pins, a pair of needle nose pliers and a hockey puck.

http://www.homegunsmith.com/cgi-bin/...structions.pdf

I followed the instructions for assembling the weapon and got it right. Check the positioning of the Safety Shield, Part 15 to insure it’s hooked over the retaining pin, before inserting the Safety Bar.

Read Part 22 of the Guide.



Once the Safety Bar is in position with the round side on the left, almost flush within the frame, slide the Safety Clip into the grooved notch at the end of the pin. You have to slightly pull back on the hammer to get it just right.



Once the Safety Clip has been placed on, depress the Safety on the right side. The square button is slightly recessed into the square hole. The Safety is now on. Trying cocking the hammer and pulling the trigger. The safety should be functional. The square side goes into the hammer and blocks it.



The Open for loading position. Notice the round end Safety Bar/Pin is extended to the left. Holding the pistol by the barrel, position the thumb on the left Barrel Latch Knob and the forefinger on the right knob. Slide them towards the grips, and then pull the barrel down. For reloading. If the barrels will not open check the position of the safety. Slightly draw back on the hammer to ease pin movement.

I had to replace both parts because the previous owner had marred the grooved notch around the Safety Bar. Trying to force the barrels open with the safety off doesn’t work. . The front of the hammer is notched and blocks the barrel latch knobs from moving.

So thanks to Practical Tactical I got the parts, did the repairs. This 20 Year old predecessor to the Judge and the Governor is now operational. For $5.00 in parts cost.
Slowhand is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 10:52 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.06998 seconds with 9 queries