The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > Gear and Accessories

Reply
 
Thread Tools
Old March 31, 2012, 05:17 PM   #1
Arch Angel
Junior Member
 
Join Date: March 31, 2012
Posts: 6
1911 Finish and Kydex

I carry my G22 in a kydex holster with no problems at all. Monday I get to pick up my Kimber Compact CDP. I have been reading complaints on other forums about kydex being hard on the finish. Since I don't have a ton of money to spend on holsters (been there done that), I'm looking to make a good decision between Kydex and leather. Can someone chime in with their experience?
Arch Angel is offline  
Old March 31, 2012, 05:49 PM   #2
RickB
Senior Member
 
Join Date: March 1, 2000
Location: Western WA
Posts: 5,699
I find that kydex holsters have a few internal "hot spots" that wear heavily on a gun's finish. A blued gun will be worn down to bare metal in these spots after relatively few draw/holster strokes. Leather holsters will also wear a finish, but it will be spread over larger areas, especially sharp edges, and not so noticeable.
RickB is offline  
Old March 31, 2012, 07:07 PM   #3
Arch Angel
Junior Member
 
Join Date: March 31, 2012
Posts: 6
This is rather bad news since I like to shoot my guns, but I also want them to stay looking like new!! And suggestions?
Arch Angel is offline  
Old April 1, 2012, 11:51 AM   #4
MagnumWill
Senior Member
 
Join Date: March 18, 2009
Location: Central Colorado
Posts: 698
Quote:
A blued gun will be worn down to bare metal in these spots after relatively few draw/holster strokes.
While possibly true, i'm not entirely convinced on the "few". Methinks the holster is much too tight.

I have been carrying my Colt New Agent .45 in a CrossBreed Supertuck IWB holster, which is horsehide/kydex hybrid. I draw it every time to put my holster on, and then replace it. I've been doing this 3-4 times per week for about eight months now, and the only markings I can find on the gun is the very front of the slide where my pants themselves have made the finish slightly lighter (and it may have always been like that), and a pinpoint mark on the front of the triggerguard where the gun is supported. If I clean the gun with a Hoppe's #9 silicone cloth, the marks disappear. It's almost as if the marks have been made by the same abrasiveness as a fingernail. The effect may be pronounced with different holsters, but my CB treats my gun very well. And I know my Colt is an expensive piece, but I didn't buy it to put it in a display case; I bought it to come with me wherever I go. Yes, the sad truth is your gun will start to get a little holster worn, but the easy solution is this:

If you want your gun's finish to stay beautiful - Keep it in a nice padded case and use it for range only.

Get a carry gun that you won't feel bad about carrying. I'm not saying beat the tar out of it- just don't sweat it when it gets a little holster rash.
__________________
Generally speaking holes in anti-gun theories are called "facts."
-Madcap_Magician
MagnumWill is offline  
Old April 1, 2012, 06:18 PM   #5
Kreyzhorse
Senior Member
 
Join Date: April 12, 2006
Location: NKY
Posts: 11,482
Leather is generally much easier than kydex on a guns finish. With that said, all holsters will create wear. If I were you, I'd buy a leather holster, shoot your gun and enjoy it, wear happens.
__________________
"He who laughs last, laughs dead." Homer Simpson
Kreyzhorse is offline  
Old April 1, 2012, 08:24 PM   #6
AK103K
Senior Member
 
Join Date: May 1, 2001
Location: PA -- In the shadow of the Shade
Posts: 7,935
As RickB stated, guns carried in kydex holsters usually have a few hot spots of wear, with basically no wear elsewhere. I suppose the timing of it depends on the guns finish.

My experience with leather has been that it wears the guns finish more overall, and leaves it looking worn, washed out and faded over time. You also have the rust issue if you sweat a lot, one thing kydex pretty much eliminates.

This is my old Colt Commander. It started out as a nice Colt blue, and lasted about a year in a couple of Galco Royal Guards before rust set in and it needed to be refinished. What you see here is the hard chrome refinish after 10+ years of hard daily use in a Blade Tech kydex IWB. The "black" streaks are actually polished chrome, and not black. They look like a mirror in person. They didnt appear overnight, more like over a couple of years. The kydex and HC knocked down 99% of the rust issue, but I still got a little "powder" like rust at and under the grip panel on the body side of the gun where it was exposed to my body now and then.




No matter what you choose, if you use and carry your gun, its going to get beat up. You might as well accept that right off. If you cant live with that, then dont carry it, and find something you arent as worried about.
__________________
“The enemy is anybody who's going to get you killed, no matter which side he is on.”
― Joseph Heller, Catch-22
AK103K is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 08:18 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.06986 seconds with 9 queries