The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > Handloading, Reloading, and Bullet Casting

Reply
 
Thread Tools
Old March 30, 2012, 10:32 PM   #1
GregInAtl
Senior Member
 
Join Date: December 29, 2010
Location: Gwinnett County Georgia
Posts: 743
Inconsistent load data

I have noticed some inconsistencies in the load data provided by several load manuals as well as that provided on powder mfgrs web site.

Example:
Lymans 49 suggest for 45acp 3.5 gr of Bullseye for 185gr jacketed HP but only 3.4 gr of Bullseye for 200gr jacketed HP but 3.8 gr of Bullseye for 230gr TMJ.

It lists 4.4gr 231 but only 3.5gr HP38 for 185gr jacketed HP when they are supposedly the same powder.

It lists 4.4gr 231 OAL 1.175 for 185gr JHP and then jumps up to 5.5gr 231 OAL 1.178 for 200gr JHP and then only 5.2 gr 231 OAL 1.275 for 230gr FMJ

I realize the bullet types are different but I wouldn't think it would make that much difference. The OALs are different but in some case almost the same. In some cases the powder wt goes down as bullet wt goes up and in other cases the powder wt goes up as the bullet wt goes up.

On Alliants website, they list 5.7 gr Bullseye OAL 1.26 for Speer 230gr TJM RN but only 5.0 gr Bullseye OAL 1.20 230 gr Speer GDHP. That seems like quite a variance. I wouldn't think the bullet types would make that much difference and the OAL is only .06 difference. The 5.7gr Bullseye is quite a bit different than Lymans 5.2 for almost the same OAL (1.26 vs 1.275) for almost the same bullet type.

What's up with this, it's enough to make your head spin.
__________________
"The worst place to have your happiness is in sombody else's head" -Lester Sumrall
GregInAtl is offline  
Old March 30, 2012, 11:14 PM   #2
jepp2
Senior Member
 
Join Date: December 24, 2008
Location: Loveland, CO
Posts: 1,310
Quote:
I have noticed some inconsistencies in the load data provided by several load manuals as well as that provided on powder mfgrs web site.
Is this a surprise to you? Rather than call them inconsistencies, I think variables might be more accurate.

The differences you see can also be impacted by different powder lots, different testing equipment which can result in significantly variations in chamber volume, different brass casings, different primers, as you mention different bullets, different pressure monitoring equipment, and so on and so on.

That is just one of the reasons why folks will always suggest you check multiple sources before selecting your starting load. It is why you should always start near the minimum load (and I have seen the minimum load in one manual above the maximum load in another for seemingly the same load).

I personally find it challenging to pick a starting load when the pressure isn't provided. The Alliant website only lists a single powder loading. For the 9mm which is a high pressure round with a huge range of OAL (can be as short as 1.010" to the SAAMI max of 1.169" and as little as 0.020" can significantly spike pressure.

That is why reloading is an interesting hobby and why QuickLoad is so helpful.
jepp2 is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 06:28 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.06534 seconds with 9 queries