The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > Handloading, Reloading, and Bullet Casting

Reply
 
Thread Tools
Old March 14, 2012, 04:02 PM   #1
4T4MAG
Senior Member
 
Join Date: April 28, 2009
Posts: 143
Case neck catching on expander

I am sizing some 22-250 rem. shells. I am using a Redding FL sizer die with a single state RCBS press with a RCBS #3 shell holder. I load several other rifle and straight wall cases. I have never run in to this problem. I am getting bent rims on the case neck. I have to wiggle the brass to make sure it does not catch on the botton of the expander ball and dent the rim. The shell holder #3, according to the chart is correct. Usually, my brass while sitting on the ram raises nearly straight and enters the die with no problem. Any ideas?
4T4MAG is offline  
Old March 14, 2012, 04:40 PM   #2
mehavey
Senior Member
 
Join Date: June 17, 2010
Location: Virginia
Posts: 2,865
Quote:
have to wiggle the brass to make sure it does not catch on the botton of the expander ball and dent the rim.
Totally normal. (I usually guide my cases by hand until settled in as a matter of course anyway.)
The smaller .223 case neck diameter just makes that step a little more noticeable.
mehavey is offline  
Old March 14, 2012, 05:25 PM   #3
BigJimP
Senior Member
 
Join Date: February 23, 2005
Posts: 11,338
I'd check for grit ...around the case holder...or in the threads of the die...something causing the case not to go straight up into the die.

On some presses - there is an adjustment on how the case fits into that resizing station...

but a little grit in there...can cause it to wobble a little and jam .../ or if your press isn't really solid on the bench ...it doesn't take much to get the case to wobble..which is probably what is causing the issue.
BigJimP is offline  
Old March 14, 2012, 05:46 PM   #4
HiBC
Senior Member
 
Join Date: November 13, 2006
Posts: 3,612
Also,is the spindle centered in the die?.If not,it may be bent or ,sometimes they just do not find home when you tigten the lock nut.With a brass in the die,ram up,the decap pin is holding the spindle centered pretty well.Try loosening and re-tightening your spindle lock ring.

I think Hornady makes a carbide elliptical expander ball or spindle that is designed to retrofit to RCBS dies.I do not know if that can be used in a Redding.

Forster's benchrest dies are a little different,The expander is higher on the spindle,just below the case shoulder.Alignments ought to be better there.

If you get annoyed enough,the price of the Forster die may be worth it.

You may be able to chuck up your spindle in a drill press or lathe and stone a little better lead in on the spindle tip.
HiBC is offline  
Old March 14, 2012, 06:44 PM   #5
langenc
Senior Member
 
Join Date: August 19, 2007
Location: Montmorency Co, MI
Posts: 1,187
Make sure the nut on the shaft that holds the decapping pin is tight. If loos that can cause some 'offcentering' of the expander ball. Lube the inside of the case neck makes the expander go in/out much easier.
langenc is offline  
Old March 14, 2012, 09:14 PM   #6
4T4MAG
Senior Member
 
Join Date: April 28, 2009
Posts: 143
It is a brand new die set from Brownell's. I really hope it's not bent out of shape.
4T4MAG is offline  
Old March 15, 2012, 12:45 AM   #7
Ideal Tool
Junior member
 
Join Date: October 6, 2010
Location: Michigan
Posts: 1,080
Hello, 4T4Mag. I had this problem when loading .222 Rem. Easiest if you have access or know someone with lathe..a portable drill will do, if you can clamp in place. Chuck that expander button up & using first coarse, followed by med. hones & plenty of oil, stone a radius on end of button. All the major loading companies in the past did this before shipping dies...just another extra quality step lost due to the bottom line mentality of today.
Ideal Tool is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 06:38 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.07836 seconds with 9 queries