The Firing Line Forums

Go Back   The Firing Line Forums > The North Corral > Black Powder and Cowboy Action Shooting

Reply
 
Thread Tools
Old March 9, 2012, 02:12 AM   #1
dlbarr
Senior Member
 
Join Date: October 8, 2011
Posts: 160
Replaced the nipples on Piettas...

Been having trouble with ignition on both '51 & '58 Piettas so I spent bank to get replacements from TOW. The '58 lit those #11s over & over again, no misfires at all. So I'm satisfied there.

The '51 however, wouldn't ignite one cap with those new nipples, not one....unless I turned them out about a full turn. So, do I understand that you can shim the nipples? Where do you get the shims....or do you have to make 'em??
dlbarr is offline  
Old March 9, 2012, 05:32 AM   #2
Andy Griffith
Senior Member
 
Join Date: May 14, 2009
Location: Macon Co. NC
Posts: 569
If these are the same nipples as installed on the other one, I've got a couple of questions...

Is the nose of the hammer that strikes the cap dished out? If so, the easiest way to make them fire is to take down some of the inside of the round part of the hammer where it contacts the frame. The other method is to get a new hammer in one of the cheap kits (which contains the trigger, hand, spring and etc) distributed by Cabelas for the 51/60.
__________________
Barney Fife: "Nip it, nip it, nip it!"
Andy Griffith:"Oh now Barn'...."
Andy Griffith is offline  
Old March 9, 2012, 08:30 AM   #3
emishi
Member
 
Join Date: November 9, 2008
Location: South Carolina
Posts: 32
Piettas

Having a pair of 1851's which I've had to finish hand fitting and cleaning up some poorly formed frame castings, my first question is... does the arbor end sit flush in the hammer channel where it comes thru the frame? I've had to diamond file one of mine flush to ensure the hammer wasn't connecting with it in the lowered position. If it's not flush in the channel, it could keep the hammer nose a bit too far from the nipple, striking the inner arc instead. Just something to check before another outlay of cash.
emishi is offline  
Old March 9, 2012, 11:38 AM   #4
Fingers McGee
Senior Member
 
Join Date: March 19, 2008
Location: Missouri
Posts: 1,860
What emishi said. I've had a couple Piettas that had this problem. It's esy to spot, there will be a dimple/mark on the hammer arch where it's hitting the frame.
__________________
Fingers (Show Me MO smoke) McGee - AKA Man of Many Colts - Alter ego of Diabolical Ken; SASS Regulator 28564-L-TG; Rangemaster and stage writer extraordinaire; Frontiersman, Pistoleer, NRA Endowment Life, NMLRA, SAF, CCRKBA, STORM 327, SV115; Charter member, Central Ozarks Western Shooters
Cynic: A blackguard whose faulty vision see things as they are, not as they should be. Ambrose Bierce
Fingers McGee is offline  
Old March 9, 2012, 09:06 PM   #5
Hellgate
Senior Member
 
Join Date: November 18, 2010
Location: Orygun
Posts: 526
It is easy to shim nipples. Take soft fine steel or bronze wire and coil it around a nail or screw shank about 10 times to make a spiral the diameter of the threaded shank on the nipples. Then with wire cutters snip them off and you end up with a pile of what look like lock washers. I then I take a small hammer and flatten them on the vise pounding surface or an anvil to the desired thickness. They resemble small open ended washers. Slip one onto the shank of the low nipple and screw it in. I use anti-seize lube or heavy lithium grease on the threads so I can get the nipples back out. If the nipple is too high, pound the shim flatter or find some finer wire. If it still isn't tall enough, use two shims or get a thicker piece of wire to start over with. I've done this on several guns and have had no problems with it. If you have too high of a nipple then the hammer face gets battered and may not fire the other nipples or it will get burrs on it that may lift spent caps off the nipples and drop them into the action.
__________________
With over 15 perCUSSIN' revolvers, I've been called the Imelda Marcos of cap & ball.
SASS#3302 (Life), SASS Regulator, NRA (Life), DGB#129
Wolverton Mtn. Peacekeepers (WA), former Orygun Cowboy (Ranger, Posse from Hell)
Hellgate is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 06:17 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.06611 seconds with 9 queries