The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > Handloading, Reloading, and Bullet Casting

Reply
 
Thread Tools
Old February 16, 2012, 10:43 PM   #26
tobnpr
Senior Member
 
Join Date: August 1, 2010
Location: Tampa Bay
Posts: 2,837
As mentioned above, it often helps to go 1/2- 3/4 turn past contact with the shellplate.

I didn't have a chambering issue, but I was checking headspace with a gauge for a bolt gun and wanted to bump the shoulders back .002 less than the fireformed brass. Couldn't make it happen.

Then someone suggested what I did above. There can still be some "slack" when you adjust for light contact. Adjust it so that it really cams over hard- and it'll bump the shoulders back.

The cautionary note above is legit, although I really don't think the manufacturers' tolerances will allow for enough bump to cause a headspace issue unless you've done some grinding on the die base...

Best to get a heaspace gauge, then you know for sure. Can't beat the Hornady Lock N Load:

http://www.hornady.com/store/Lock-N-...h-Body-1-Each/


And, you should go with small base sizing dies for an AR. Guarantee it'll help with the sizing issues.

Last edited by tobnpr; February 16, 2012 at 10:50 PM.
tobnpr is offline  
Old February 17, 2012, 12:24 PM   #27
ctrain831
Junior Member
 
Join Date: February 15, 2012
Posts: 11
Problem solved......hopefully

I believe I've fixed the issue. A trip to the range this afternoon will tell. It was definitely a neck tension issue. I had adjusted the sizing die's decapping/expander screw improperly. After re-reading adjustment instructions I saw where I made my mistake. It was a stupid one, considering I'd adjusted the .308 dies properly, I don't know why I screwed up the .223. I guess I wasn't focused. Thanks to all for the tips. Most of you had the problem pegged. This time I'm taking the first 20 rounds to the range before I start cranking 'em out. Another lesson learned the hard way. I'll let u know how it goes. Thanks
ctrain831 is offline  
Old February 18, 2012, 04:03 AM   #28
HiBC
Senior Member
 
Join Date: November 13, 2006
Posts: 3,517
ctrain,I live in FtC.PM me.
HiBC is offline  
Old February 19, 2012, 01:05 AM   #29
ctrain831
Junior Member
 
Join Date: February 15, 2012
Posts: 11
Problem officially solved!

The new cartridges work great. It was definitely a neck tension issue. Thank you for all of the assistance, it definitely pointed me in the right direction and gave me a deeper understanding of the inner workings of the sizing/expander die. I was going through the motions without proper understanding. Now comes the fun of bullet pulling and reloading all of the screw-up rounds - a small price to pay for a valuable lesson. Also...taking the NRAs metallic cartridge reloading course next month to get some further knowledge.

HiBC - Good to know there's a veteran in the area that willing to share some expertise. I'm sure I'll need a hand in the future and will PM you when the time comes.
ctrain831 is offline  
Reply

Tags
223 , failure , reload , vmax

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 07:35 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.06268 seconds with 9 queries