The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > Handloading, Reloading, and Bullet Casting

Reply
 
Thread Tools
Old February 6, 2012, 09:49 PM   #1
603Country
Senior Member
 
Join Date: January 6, 2011
Location: Thornton, Texas
Posts: 2,109
223 Neck Sizing Die

I'm going to buy a neck sizing die for my 223, and I could use some advice on which one to get. People have said on this forum that the Lee collet dies are excellent and relatively cheap. Is that a better choice than the more expensive versions just because it's less money for the same quality of performance? Somebody educate me. Thanks.
603Country is offline  
Old February 6, 2012, 09:53 PM   #2
4runnerman
Senior Member
 
Join Date: January 16, 2010
Location: Minnsota
Posts: 2,656
I just got the Redding version a few days ago.I have only loaded 10 rounds at the moment to test. Have not got a chance to shoot them yet to see the difference in accuracy.( if there is any at all). All my other Dies are Lee and i could not be happier. They are very good,low cost dies.
__________________
NRA Certified RSO
NwCP- Performance Isn't Optional
4runnerman is offline  
Old February 6, 2012, 10:04 PM   #3
Tim R
Senior Member
 
Join Date: November 30, 2004
Location: God's side of Washington State
Posts: 1,601
I use a Horaday bushing die. I believe Redding has one too. The nice part of the bushing die is you can adjust neck tension and how much the neck grips the bullet by a simple bushing change. A chart is supplied with the instructions and how to figure out what bushing to get.
__________________
God Bless our Troops especially our Snipers.
Tim R is offline  
Old February 6, 2012, 10:05 PM   #4
jepp2
Senior Member
 
Join Date: December 24, 2008
Location: Loveland, CO
Posts: 1,276
The Lee die will produce sized brass with less neck runout than any other neck sizing die. And it is the easiest to use since no lube is required. It does take a bit of learning to use it properly. Reading the directions and following them is a good start.
jepp2 is online now  
Old February 6, 2012, 10:09 PM   #5
625cnd
Member
 
Join Date: June 9, 2011
Posts: 21
Neck Sizing is only for bolt action guns. Neck sizing can be done with a FL sizer die, just back off the die about the width of a nickel. This will just size the neck and not bump the shoulder. Just a thought

I would suggest that consider a Forster Neck Die. As their expander ball is mounted higher then other brands. But, a Redding neck die with a carbide expander ball added would lessen the work hardening of the brass.

The use of a Type S Redding die requires a bushing, and the you have a reading of your brass of choice neck wall thickness. Then one would just want to use the bushing to control your neck tension,

Eventually you wiill need to bump the shoulder....usually after 5 or so firings.
A Redding Body die will leave the neck alone, but bump the shouler back to allow for reliable chambering of your brass.
625cnd is offline  
Old February 6, 2012, 10:11 PM   #6
m&p45acp10+1
Senior Member
 
Join Date: May 3, 2009
Location: Central Texas
Posts: 3,307
I use the Lee collet die, and the dead length seating die for .223 Rem. Shooting my reloads out of a Savage Model 12 with heavy target barrell will give me half MOA on a crappy day.
__________________
No matter how many times you do it and nothing happens it only takes something going wrong one time to kill you.
m&p45acp10+1 is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 09:50 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2013 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.06813 seconds with 9 queries