The Firing Line Forums

Go Back   The Firing Line Forums > The North Corral > Curios and Relics

Reply
 
Thread Tools
Old January 23, 2012, 02:01 PM   #1
hammered54
Senior Member
 
Join Date: September 28, 2010
Location: Pinckney,Michigan
Posts: 107
Whitney Arms Co.

I was going thru a bunch of old stuff of my Dads and found this old rifle.
it's a Whitney Arms 22cal rolling block Rifle, I believe its whats called a "sporting rifle #1. ser. # 72656
now the stock is missing and a few other parts but I thought it would be cool to see if I could get this old thing up and running and hang it over the fireplace.

now the question is...what do you think the chances of finding any parts for this?
the spring for the hammer and the ejector piece which mates to the rolling block are missing along with the screw that hold the bracket with the pins on it that holds the hammer and rolling block into the body of the gun.

I'll try and post a few photos of this rifle a little later tonight as its soaking in mineral sprites now ( its a little rusty )

thanks Matt.
hammered54 is offline  
Old January 23, 2012, 02:40 PM   #2
James K
Staff
 
Join Date: March 17, 1999
Posts: 19,179
I think finding parts would be next door to impossible. Those guns are fairly simple, and there are some diagrams/pictures around, so having the stock and other parts made would not be impossible, just not feasible economically since the cost would be much more than the gun would be worth.

Most incomplete and broken guns in boxes were put there because someone, probably your Dad, found out that they were not repairable. I am afraid you will find the same thing.

Jim
__________________
Jim K
James K is offline  
Old January 23, 2012, 06:53 PM   #3
mdevlin53
Member
 
Join Date: January 7, 2012
Location: new york
Posts: 21
I have a box of gun too. It is a Whitneyville 22 short pistol. i am missing the cylinder and side plate and a pair of grips. I had absolutly no luck finding any parts at all. probably have to keep eyes open at shows shops and yardsales. good luck
mdevlin53 is offline  
Old January 23, 2012, 08:52 PM   #4
Avenger
Senior Member
 
Join Date: September 29, 2008
Posts: 272
Well, you can probably find a "good-enough" fix for the missing screw in the hardware aisle. The hammer spring might take some doing, but I wouldn't be surprised if you could find something that could be adapted to work in the depths of a McMaster-Carr catalog.
Avenger is offline  
Old January 24, 2012, 11:59 AM   #5
gyvel
Senior Member
 
Join Date: August 30, 2009
Location: Northern AZ
Posts: 4,829
Hate to state the obvious, but has anyone tried Dixie Gun Works?

It seems to me that, a few years back, they advertised a pile of unsorted Whitney parts.

Last edited by gyvel; January 25, 2012 at 02:09 AM.
gyvel is offline  
Old January 25, 2012, 01:12 AM   #6
OcelotZ3
Senior Member
 
Join Date: March 20, 2008
Posts: 170
Also check Remington stocks. There was a lot of crossover.
OcelotZ3 is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 04:36 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.07410 seconds with 9 queries