The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > The Smithy

Reply
 
Thread Tools
Old November 29, 2011, 07:59 AM   #1
oneoldsap
Senior Member
 
Join Date: September 16, 2009
Location: I live in the foot of the Green Mountains of Vermont
Posts: 1,585
Rem. Model 11

I have to disassemble one of these for refinishing . Can anyone tell me how to remove the bolt ? It's different than the A-5 , and Steve's pages had just a parts schematic for it .
oneoldsap is offline  
Old November 29, 2011, 12:29 PM   #2
Scorch
Senior Member
 
Join Date: February 13, 2006
Location: Washington state
Posts: 11,461
Unless it's a Sportsman, it's pretty much the same as an A5. 20 gauges are a bit trickier, but Model 11s are the same design as the A5, follow the same procedures. Remove forearm, remove barrel, remove stock, remove recoil spring retainer pin, remove trigger group, remove carrier, remove bolt handle, remove crosspin, remove bolt.
__________________
Never try to educate someone who resists knowledge at all costs.
But what do I know?
Summit Arms Services
Taylor Machine
Scorch is offline  
Old November 29, 2011, 02:34 PM   #3
oneoldsap
Senior Member
 
Join Date: September 16, 2009
Location: I live in the foot of the Green Mountains of Vermont
Posts: 1,585
This one is a 16 Ga. and it doesn't have the little cutout in the receiver , that lets you get a punch in to tap out the cross pin . I'm about ready to throw it on the mill and make my own cutout . Have you ever seen one without the cutout ? There's a video on U-Tube that is very good except his gun is a 12 Ga. with the cutout and a very different bolt . I guess I'm stumped till someone comes along that knows the 16 Ga.
oneoldsap is offline  
Old November 29, 2011, 04:37 PM   #4
Goatwhiskers
Senior Member
 
Join Date: April 8, 2009
Location: Batchelor, La.
Posts: 470
The pin is removed on all models Rem and Browning by inserting a proper size punch thru the small hole in the Left side of the receiver, tapping the pin out thru the breech opening on the right. Goat
Goatwhiskers is offline  
Old November 30, 2011, 10:09 AM   #5
oneoldsap
Senior Member
 
Join Date: September 16, 2009
Location: I live in the foot of the Green Mountains of Vermont
Posts: 1,585
Puzzeling for sure

I know how it's supposed to come apart . The problem is that the hole on the left side of receiver that is supposed to line up with the pin , doesn't . There is also no cutout in the receiver to push the latch/link pin out through the ejection port . I just took some pictures of it and can email them to whoever wants to see this freaky thing !
oneoldsap is offline  
Old December 1, 2011, 03:52 PM   #6
oneoldsap
Senior Member
 
Join Date: September 16, 2009
Location: I live in the foot of the Green Mountains of Vermont
Posts: 1,585
Got it , Thanks . moderator please close Thread !
oneoldsap is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 01:07 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.07186 seconds with 9 queries