The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > The Smithy

Reply
 
Thread Tools
Old November 25, 2011, 10:41 AM   #1
adamhills
Junior Member
 
Join Date: November 25, 2011
Posts: 1
can't put my Remington 700's safety on

Hi,
newbie here. I just purchased a brand new 30-06 Remington 700 BDL. I have not loaded or chambered any bullets yet. I am concerned because I can not put the safety in safe mode unless the bolt has been lifted and the gun has been cocked. Is this normal for the Remington 700? This is a brand new gun straight out of the box.
Thanks,
Adam
adamhills is offline  
Old November 25, 2011, 02:14 PM   #2
john323
Member
 
Join Date: June 16, 2009
Location: MONTEREY PARK , CA
Posts: 74
That's normal.
__________________
johnsgunsmithing@live.com

Southern California
Anything legal, Rifles, Handguns, Shotguns, Black powder
john323 is offline  
Old November 25, 2011, 02:25 PM   #3
edward5759
Senior Member
 
Join Date: September 15, 2009
Location: Phoenix, AZ. 30 miles from water, two feet from Hell.
Posts: 354
Have FUN with your new rifle their a hoot to shoot.
__________________
Failure is part of success!

This year will go down in history. For the first time, a civilized nation has full gun registration. Our streets will be safer, our police more efficient, and the world will follow our lead into the future!" -Adolf Hitler,1935"
edward5759 is offline  
Old November 26, 2011, 08:58 PM   #4
Gbro
Senior Member
 
Join Date: February 20, 2005
Location: Minnesota
Posts: 2,056
Be sure you fully understand the workings of the "J" Lock integral safety locking device. The device must be fully in "Lock" or Un-"Lock", and the key device can be removed while the lock is in-between the to modes which can also lead to confusion and inoperative condition.
__________________
Gbro
CGVS
For the message of the Cross is foolishness to those who are perishing, But to us who are being saved, It Is The Power Of God. 1Corinthians 1-18
Gbro is offline  
Old November 26, 2011, 10:38 PM   #5
419
Member
 
Join Date: June 21, 2010
Posts: 46
That is normal for a 700. It must be cocked to engage the safety.
419 is offline  
Old November 28, 2011, 07:44 PM   #6
James K
Staff
 
Join Date: March 17, 1999
Posts: 19,124
When you think about it, there would be no reason to engage the safety if the rifle isn't cocked.

BTW, do NOT try to uncock the bolt with a round in the chamber. Not only could you slip and the rifle will fire, but if the bolt is uncocked, the firing pin will rest right on the primer, not a good idea even though the new 700's shroud the rear of the cocking piece so it is unlikely to be struck by anything.

Jim
__________________
Jim K
James K is offline  
Old November 28, 2011, 08:03 PM   #7
rantingredneck
Senior Member
 
Join Date: January 12, 2007
Location: North Carolina
Posts: 4,728
Your 700 is functioning normally. You cannot engage the safety with the firing pin down. I have two and have hunted with them for many years. Enjoy your rifle.
__________________
NRA Member
NC Hunter's Education Instructor

PCCA Member (What's PCCA you ask? <- Check the link)
rantingredneck is offline  
Old November 29, 2011, 08:10 AM   #8
oneoldsap
Senior Member
 
Join Date: September 16, 2009
Location: I live in the foot of the Green Mountains of Vermont
Posts: 1,584
Read Manual

Your brand new Model 700 came with a manual that says to read it before using this product . It even says it right on the barrel !
oneoldsap is offline  
Old November 29, 2011, 01:28 PM   #9
James K
Staff
 
Join Date: March 17, 1999
Posts: 19,124
Read the manual.
What's a manual?
It is a book.
What's a book?

I notice that some of the younger folks can't read anything unless it is on a screen of some kind, and the smaller the screen the better.

Jim
__________________
Jim K
James K is offline  
Old November 29, 2011, 01:50 PM   #10
mapsjanhere
Senior Member
 
Join Date: August 6, 2009
Location: Albuquerque
Posts: 2,342
Now you've done it. How long until a lawyer will demand LCD screens in every stock with the warnings continuously scrolling. Try to color match that with oiled walnut.
__________________
F 135 - the right choice
mapsjanhere is offline  
Old November 29, 2011, 10:02 PM   #11
jason75979
Senior Member
 
Join Date: February 1, 2009
Location: Southeast Texas
Posts: 100
Tough crowd today!
jason75979 is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 07:15 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.08408 seconds with 9 queries