The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > The Smithy

Reply
 
Thread Tools
Old November 10, 2011, 02:07 PM   #1
bigj480
Junior Member
 
Join Date: August 11, 2009
Posts: 4
Removing rust without excessive finish damage?

I just got a chance to look at some guns my dad has neglected. The have varying degrees of rust from light specs to some that surely have considerable pitting. I'm going to clean the bores for now but what about the outer surface and interior of the receivers? I don't want to do ANY damage that I can avoid. I've read that 0000 steel wool with oil is good, then I read that the oil is bad because it keeps the rust there and that steel wool is too aggressive. What about brass or copper wool? What about special pads like THIS ONE? What about using electrolysis? It seems pretty easy, just a battery charger and some basic materials.

The guns are 2 Westernfield lever action 30-30s, one Winchester Model 94, 1891 Argentine Mauser, Universal M1 carbine, a couple shotguns and some 22LRs. It's a shame he let them sit for so long and they went through a flood...
bigj480 is offline  
Old November 10, 2011, 02:12 PM   #2
Don P
Senior Member
 
Join Date: December 17, 2005
Location: Florida
Posts: 4,786
Quote:
February 23, 2008, 10:48 PM #1
JohnKSa
Staff


Join Date: February 12, 2001
Location: DFW Area
Posts: 14,735 Removing rust on blued surfaces--do NOT use oil!!!

--------------------------------------------------------------------------------

Use 0000 steel wool DRY.

The removed rust is an abrasive, if you put oil on the metal surface or on the steel wool, the removed rust is retained and rubbed on the surface which can damage the finish.

If you use the steel wool DRY, shake it out frequently and keep the surface of the gun dusted off the removed rust doesn't get rubbed around on the finish, minimizing the damage to the remaining finish.

You can oil the metal surfaces AFTER the rust has been removed but you want them to be as dry as possible while you're actually using the steel wool.

I'm posting this because I see a lot of people recommending the use of oil and steel wool to remove rust and I know from experience that is much harder on the finish. I used to have a friend with a gun shop and I would go over all the used guns each week to keep them oiled and rust free. Since they were out in the customer area, not behind the counter, they had been handled and some would build up light surface rust. I would oil them if they weren't rusty and remove the surface rust if they were rusted. It was easy to see the difference between using the steel wool with oil and without.
__________________

Did you know that there is a TEXAS State Rifle Association?
Check out Black Bear Flashlights.
To lend a helping hand, at the top of the page there is a search button, just click on it type in rust removal and here is what I found
__________________
NRA Life Member, NRA Range Safety Officer, IDPA Safety Officer
As you are, I once was, As I am, You will be.
Don P is offline  
Old November 10, 2011, 10:53 PM   #3
James K
Staff
 
Join Date: March 17, 1999
Posts: 19,333
FWIW, I do NOT recommend steel wool, either oiled or dry. The best I have found is bronze (brass) wool or copper wool, sold as pot cleaners in your local super market. Steel wool WILL scratch fine bluing, no matter what anyone says (they haven't looked at the surface under magnification). Steel wool may be necessary, but use it only if necessary - try the brass or copper first.

Jim
__________________
Jim K
James K is offline  
Old November 10, 2011, 11:07 PM   #4
bigj480
Junior Member
 
Join Date: August 11, 2009
Posts: 4
Quote:
Originally Posted by Don P
To lend a helping hand, at the top of the page there is a search button, just click on it type in rust removal and here is what I found
Thank you, I did search before posting and found that exact post. So far that is the only post I have found recommending keeping things dry, just looking for some other opinions. I also wanted to know if that cleaning pad or brass wool/pot scrubbers might be a better thing to use than 0000 wool.
bigj480 is offline  
Old November 10, 2011, 11:30 PM   #5
Ideal Tool
Junior member
 
Join Date: October 6, 2010
Location: Michigan
Posts: 1,080
Hello, bigj480. If you can find some copper or brass sheet..about 1/32" to 1/16" thick..about 1/2" wide or so. file end flat with sharp edges & flood area with very light oil or Hoppes..use in a scraping motion..this will take off rough rust above surface..there more than likely is going to be pitting..and nothing will get rid of that except polishing down past bottom of pits.
Ideal Tool is offline  
Old November 11, 2011, 03:09 AM   #6
4V50 Gary
Staff
 
Join Date: November 2, 1998
Location: Colorado
Posts: 16,777
I do the same thing as Ideal Tool suggests except with a 1982 or earlier copper penny. A bit of oil and scrape, scrape, scrape. Steel wool is tool harsh and will remove the finish. Copper is softer than steel and will leave a light yellow patina that will come off in time.

You asked about copper scouring pads. Well, as they are less rigid they will take longer than a penny or a piece of scrap brass. I use pieces of copper scouring pads to clean the bore of lead build-up.

BTW, I would avoid steel wool, even 0000 steel wool.
__________________
Vigilantibus et non dormientibus jura subveniunt. Molon Labe!
4V50 Gary is offline  
Old November 11, 2011, 04:30 AM   #7
natman
Senior Member
 
Join Date: June 24, 2008
Posts: 1,416
Gentle rubbing with 0000 steel wool and oil.
natman is offline  
Old November 11, 2011, 04:34 PM   #8
bigj480
Junior Member
 
Join Date: August 11, 2009
Posts: 4
Thank you all for the replies, especially those who posted in both threads. I think I'll do the 0000 steel wool and Kroil, I'm not worried about microscopic scratches and , unfortunately, some of them are bad enough that they really need to be re-blued anyway.
bigj480 is offline  
Old November 19, 2011, 01:24 AM   #9
bonesy malone
Junior Member
 
Join Date: November 19, 2011
Posts: 2
all good ideas...but without knowing the damage and depth of the rust pits start off with a blue "non scratching" scotch bright...you're gonna have to re-blue if there is rust anyways...get as much of the rust off as u can then if needed move to a more abrasive material if the pits aren't too deep...keep in mind u don't want to take metal off past spec. limits...some areas are more giving then others...good luck!
bonesy malone is offline  
Old November 23, 2011, 12:16 PM   #10
Inspector3711
Senior Member
 
Join Date: February 9, 2008
Location: Puget Sound Washington
Posts: 1,546
The dark red Scotchbrite works well for heavy rust but will remove bluing.

If blued I would gently go over them with Flitz polish first. You may be surprised at how well it cleans them up.
__________________
"If someone has a gun and is trying to kill you, it would be reasonable to shoot back with your own gun." The Dalai Llama (5/15/01, The Seattle Times)
"That rifle on the wall of the labourer's cottage or working class flat is the symbol of democracy. It is our job to see that it stays there." George Orwell
Inspector3711 is offline  
Old November 24, 2011, 12:59 PM   #11
WESHOOT2
Senior Member
 
Join Date: February 20, 1999
Location: home on the range; Vermont (Caspian country)
Posts: 14,213
please

Brownells offers stainless steel wool so one does not need to concern oneself with carbon-steel embedding.
__________________
.
"all my ammo is mostly retired factory ammo"
WESHOOT2 is offline  
Old November 24, 2011, 01:01 PM   #12
Lee McNelly
Junior member
 
Join Date: June 9, 2011
Posts: 325
rust specks

pencil eraser
Lee McNelly is offline  
Old November 26, 2011, 07:41 PM   #13
sophijo
Senior Member
 
Join Date: June 28, 2004
Posts: 664
no brainer

1 part feed grade molasses and 9 parts water. Soak for 3 days. clean and lube.
sophijo is offline  
Old November 26, 2011, 08:22 PM   #14
jaguarxk120
Senior Member
 
Join Date: February 28, 2008
Location: Michigan
Posts: 1,934
The molasses will remove all the rust including the bluing. Bluing is a form of rust, so that mix will remove all the rust.
jaguarxk120 is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 03:12 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.09378 seconds with 9 queries