The Firing Line Forums

Go Back   The Firing Line Forums > The Hide > The Dave McCracken Memorial Shotgun Forum

Reply
 
Thread Tools
Old November 25, 2011, 01:31 PM   #1
jesterspal
Junior Member
 
Join Date: November 25, 2011
Posts: 2
broken barrel guide on 870?

I'm new to the forum and a new shooter. I have an 870 tactical and have discovered that the finger guide in the receiver that aligns the barrel is broken. Does anyone know what I will have to do to fix this?

Thanks.

photo here:
https://public.me.com/chou
jesterspal is offline  
Old November 25, 2011, 06:53 PM   #2
Goatwhiskers
Senior Member
 
Join Date: April 8, 2009
Location: Batchelor, La.
Posts: 470
That is the ejector of the gun you're looking at that will have to be replaced. Occaisionally a 'smith is lucky enough to dress off the inner end of the rivits and not have to install new ones, but normally the procedure is to grind off and knock out the old rivits, then re-rivit the new part to the frame, which calls for dressing off the head of the new rivits and usually leads to re-blueing the frame. A few, of which I am one, can measure, mark, and cut the head of the rivit before installing, then the only blueing necessary is to touch up the new rivit heads. Tools are available from Brownells for the brave. Here endeth the lesson. Goatwhiskers the Elder
Goatwhiskers is offline  
Old November 25, 2011, 07:43 PM   #3
TheKlawMan
Junior member
 
Join Date: June 23, 2009
Location: Orange County, CA
Posts: 2,149
I have heard a Remington armorer explain the problem just as Goatwhiskers describes. It takes some finesse to save those rivits.
TheKlawMan is offline  
Old November 25, 2011, 10:05 PM   #4
jesterspal
Junior Member
 
Join Date: November 25, 2011
Posts: 2
Thanks for the tips. Very helpful. Not sure if I want to tackle this myself.

I did receive this very helpful info from the writer of rem870.com:

This will take some time, parts and tools but it can be fixed.
The broken part is an ejector, you will need to remove the broken one.

Here is video how my friend and I replaced one rivet and ejector spring:
http://www.rem870.com/2011/10/25/rem...g-replacement/

You will need to remove 2 rivets, remove the broken ejector and spring.
This can be done using rivet cutter or something else.

You will need to get 2 rivets, ejector and ejector spring (not sure if the
old one will be ok).

http://www.brownells.com/.aspx/pid=0...il/870-Express

Parts #15, 14, 13 and 77.

We have used this set of tools:
http://www.brownells.com/.aspx/pid=6...AKING-TOOL-SET

This tool-set has good instructions included.

After the installation you will need to do something to fix shotgun
coating where new rivets are installed.

I would be greateful if you could take photos of the repair process to
show other owners how to fix this problem. All contributors receive my new
eBook about Remington 870 :-)

If you will have any additional questions, please, don't hesitate to
contact me.

Thanks,
Vitaly.
jesterspal is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 12:45 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.07073 seconds with 9 queries