The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > Handloading, Reloading, and Bullet Casting

Reply
 
Thread Tools
Old October 24, 2011, 09:42 PM   #1
DeerSlayer86
Senior Member
 
Join Date: October 4, 2011
Location: Tx
Posts: 117
Reloading

I want to get into reloading and would like some recommendations on gear. Presses, dies, powders, manuals, bullets(hunting) favorite loads(specifically for 308 and 25-06 rem), tips, mistakes you may have made when you got started...things like that. I just want to get the most out of my rifles and im sick of paying for "premium" ammunition. Thanks guys
DeerSlayer86 is offline  
Old October 24, 2011, 10:44 PM   #2
emcon5
Senior Member
 
Join Date: July 10, 1999
Location: High Desert NV
Posts: 1,627
Sticky, top of the forum.

http://thefiringline.com/forums/showthread.php?t=230171
emcon5 is offline  
Old October 24, 2011, 11:16 PM   #3
Lost Sheep
Senior Member
 
Join Date: January 24, 2009
Location: Anchorage Alaska
Posts: 3,003
Help us help you

If we knew some more about your shooting habits and goals. You have given us some parameters of your reasons for wanting to reload (economy, searching for ultimate accurac) but some more information would be more helpful. Your experience level, tolerance for the unknown and your budget (in money, spare time and spare space), we could advise you better.

Thanks for asking our advice. Help us help you.

Lost Sheep
Lost Sheep is offline  
Old October 24, 2011, 11:34 PM   #4
farmerboy
Junior member
 
Join Date: May 16, 2009
Location: Central Texas
Posts: 1,343
Atleast try to help yourself also by reading sticky at top of page and get and buy a manual and read it first before just trying to get someone to do everything for you if you're not willing to do your part
farmerboy is offline  
Old October 27, 2011, 03:31 PM   #5
raceroch
Member
 
Join Date: October 5, 2011
Location: RI
Posts: 51
just buy a dillon 550B and learn how to use it, you will never need another machine in your life. buy components and a pair of calipers and scale and you will be set.
raceroch is offline  
Old October 27, 2011, 04:13 PM   #6
David Bachelder
Senior Member
 
Join Date: August 23, 2011
Location: Trinity, Texas
Posts: 632
Get a manual or two, read them, then buy RCBS equipment. The Rockchucker is a good move. Best bet is to start out on a single stage press. This will teach you the How To's. When you are ready to upgrade, go to Ebay and sell the old press and get something new, or keep the old press, it will last you a lifetime.
David Bachelder is offline  
Old October 27, 2011, 05:29 PM   #7
serf 'rett
Senior Member
 
Join Date: June 25, 2009
Location: Stuttgart
Posts: 1,342
+1 on read sticky at top. Another good starter book is The ABC’s of Reloading. In my opinion, the suggestion to buy a Dillon 550, for reloading rifle, is a vast amount of overkill unless you are going to reload and shoot hundreds to thousands of rounds per month. It would be a hefty investment into something which you don’t even know if you’ll enjoy or need. Learning the ropes on a single stage (or turret) press will help you decide if you want to plunge full bore into the reloading sport. Pick up a loading manual or two and study up on reloading. Find someone who reloads and talk with them.

Warning: If you start reloading, I doubt if you will save money. With time, care and attention, you can create premium custom cartridges, which are tweaked for top performance in your rifles; however, all that money you thought you would save, well, you end up just getting to shoot a lot more.
__________________
A lack of planning on your part does not necessarily constitute an emergency on my part.
serf 'rett is offline  
Old October 27, 2011, 05:39 PM   #8
jimbob86
Senior Member
 
Join Date: October 4, 2007
Location: All the way to NEBRASKA
Posts: 6,824
Why waste $$$?

Get a Lee Anniversary kit. Best value out there: the kit and some Hornady dies will cost less than other presses by themselves. There is no functional difference between Lee's cast iron O-frame and any of the other color cast iron O-frames, save the price.

Cabela's had them (the kits) on sale for $99 last time I was in there.....
__________________
TheGolden Rule of Tool Use: "If you don't know what you are doing, DON'T."

http://nefirearm.com/
jimbob86 is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 12:31 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.07352 seconds with 9 queries