The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > Handloading, Reloading, and Bullet Casting

Reply
 
Thread Tools
Old August 6, 2011, 05:51 PM   #1
troy_mclure
Senior Member
 
Join Date: November 17, 2008
Location: gulf of mexico
Posts: 2,716
mid level .44 loads?

im looking for some mid-level .44 loads.

im shooting a ruger sbh 5.5" bbl, and ive got 240gr swc i cast.

im looking for +/-1100fps.

for this weight of boolit most special loads end below 1000fps, and most magnum loads start above 1200fps.
__________________
There is only one tactical principle which is not subject to change. It is to use the means at hand to inflict the maximum amount of wound, death, and destruction on the enemy in the minimum amount of time."
troy_mclure is offline  
Old August 6, 2011, 06:15 PM   #2
JACK308
Junior member
 
Join Date: July 10, 2011
Posts: 377
When I get mine I'l be using 240 cast SWC 18.5 grains of 2400 that pushes it about 1100 or so.Check out LYMAN 49th reloading manual more info is there.
JACK308 is offline  
Old August 6, 2011, 06:23 PM   #3
243winxb
Senior Member
 
Join Date: July 26, 2011
Posts: 1,026
10.0gr of Unique
243winxb is offline  
Old August 6, 2011, 08:11 PM   #4
mavracer
Senior Member
 
Join Date: February 27, 2008
Location: midwest
Posts: 3,022
I'll second 10.0gr of unique. Elmer's old practice load it's very accurate in every gun I've ever shot it in.
__________________
rather be judged by 12 than carried by 6
Quote:
originally posted my Mike Irwin
My handguns are are for one purpose only, though...
The starter gun on the "Fat man's mad dash tactical retreat."
mavracer is offline  
Old August 6, 2011, 08:25 PM   #5
zxcvbob
Senior Member
 
Join Date: December 20, 2007
Location: S.E. Minnesota
Posts: 4,198
10.0 of Unique ought to be a good one.

Basically you can use any .45 Colt data for 250 or 255 grain bullets in .44 Magnum, substituting a 240 grain SWC. But not if the .45 load data says "Ruger Only" or +P.
__________________
"The only way to stop a bad guy with a gun is with a good guy with a gun"

Last edited by zxcvbob; August 6, 2011 at 08:32 PM.
zxcvbob is offline  
Old August 6, 2011, 08:29 PM   #6
GeauxTide
Senior Member
 
Join Date: April 20, 2009
Location: Helena, AL
Posts: 3,080
Again with the 10gr Unique Load. I've found 8gr. to be more accurate, but it's under 1000. FYI, I use 10gr in my 45LC under 255 and 275.
GeauxTide is offline  
Old August 6, 2011, 09:55 PM   #7
totaldla
Senior Member
 
Join Date: August 10, 2009
Posts: 762
Elmer wiped his butt with a pine cone too.

There are many other powders that will do what you want. I've played with some, maybe this will help - look in the load data section of the 329pd info link. Have fun!
totaldla is offline  
Old August 6, 2011, 10:26 PM   #8
Edward429451
Junior member
 
Join Date: November 12, 2000
Location: Colorado Springs, Colorado
Posts: 9,494
19.0 gr 2400 gave me 1287fps from a 7.5" barrel, so if you went with 18.0 gr you would be right on top of what you ask for. No mag primers and give it a good crimp.
Edward429451 is offline  
Old August 7, 2011, 12:35 AM   #9
T. O'Heir
Senior Member
 
Join Date: February 13, 2002
Location: Canada
Posts: 3,336
"...this weight of boolit..." This weight of what?
"...most magnum loads start above 1200fps..." Um, no. You must be looking at 240 grain jacketed loads. Hodgdon cast bullet .44 Mag starting loads run 759 to 866 fps. Max loads run between 940 and 1334.
Win 231 or HP-38 will give you 1100 fps mid-range velocities.
Mind you, what you're planning on using the loads for matters.
__________________
Spelling and grammar count!
T. O'Heir is offline  
Old August 7, 2011, 09:07 AM   #10
WESHOOT2
Senior Member
 
Join Date: February 20, 1999
Location: home on the range; Vermont (Caspian country)
Posts: 14,270
For your goal I most highly recommend Power Pistol, HS6, and N350.

I would personally start with HS6.
__________________
.
"all my ammo is mostly retired factory ammo"
WESHOOT2 is offline  
Old August 7, 2011, 11:43 AM   #11
Slamfire
Senior Member
 
Join Date: May 27, 2007
Posts: 4,130
This load is accurate and powerful in my S&W M629

Code:
S&W M629-4 Stainless, 5" Barrel
					
240 LSWC 8.5 grs Unique  thrown, Midway Brass WLP		
25-Nov-04	T = 58 °F				
					
Ave Vel =	1023				 
Std Dev =	25				 
ES =	99				 
Low =	958				 
High =	1057				
N = 	30				
 		


__________________
If I'm not shooting, I'm reloading.
Slamfire is offline  
Old August 17, 2011, 07:46 AM   #12
RedHawk357
Member
 
Join Date: September 7, 2008
Location: Colorado Springs, Colorad
Posts: 60
Lite-Mid Level 44 Mag Loads

This is what i got from my equipment: WW or RP brass 240gr LSW mostly cast by me, moderate to heavy crimps. Avg of ten rnds.

RedDot 6.5gr/906fps avg
TiteGroup 8.8gr/1092
HP38 7.9gr/922
231 8.2gr/933
SR7625 10gr/1094
Universal 9.2gr/1083
800x 11.4gr/1095
4756 11.0gr/1053
HS6 12.9gr/1082
2400/16.8gr/1010
IMR4227 21.2gr/1064
LilGun 16.8gr/1102

I would check my math against good updated load manuals as I was recruited from the human race.
RedHawk357 is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 04:36 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.08586 seconds with 9 queries