The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > Handloading, Reloading, and Bullet Casting

Reply
 
Thread Tools
Old July 20, 2011, 09:34 PM   #1
UtopiaTexasG19
Senior Member
 
Join Date: July 3, 2011
Location: S.E. Texas Gulf Coast
Posts: 742
Initial Wetting Of Lube Pad...

On a new, never used, full casing lube pad how much oil do you apply? Can you apply too much? Thanks...
UtopiaTexasG19 is offline  
Old July 20, 2011, 10:19 PM   #2
USMC Vet
Member
 
Join Date: April 20, 2009
Location: S.E. New Hampshire
Posts: 28
initial lubing of lube pad

Yes, you can over lube (which is usually my problem). Normally on a new pad, I will pour 1 1/2-2 tbsp. of lube onto the pad, and slowly massage it into the pad with my fingertips, until a majority of the lube has been absorbed. I will then let the pad sit covered in a corner for a day or two. At that point, most of the lube has been absorbed into the pad. A little of that lube goes a fur piece.
USMC Vet
USMC Vet is offline  
Old July 21, 2011, 07:08 PM   #3
603Country
Senior Member
 
Join Date: January 6, 2011
Location: Thornton, Texas
Posts: 2,199
Way back when, I tried to use that flat RCBS lube pad, and rolled the brass gently over it, but I got either too much lube or too little on the brass. Too much caused case dents, and I found that I didn't need to lube the whole darn case anyway. I cleaned my dies and threw away that flat store-bought pad. I got an old towel and cut a piece about 12 inches square and folded it to about 3 or 4 inches square and saturated it good with RCBS lube. When I resize, I just lightly twirl the bottom inch or so of the case on the edge of the folded and lubed up towel. That's all the lube that I need. The old folded towel looks pretty nasty these days, and is truly lube saturated. I keep it in a plastic bag when I pack up my gear after I do all my loading. That'd work for ya if you aren't loading hundreds of rounds at a sitting.
603Country is offline  
Old July 22, 2011, 07:02 AM   #4
Rifleman1776
Senior Member
 
Join Date: April 25, 2010
Location: Arkansas
Posts: 3,309
I started using Dillon spray lube and never looked back.
Pads are messy and inefficient.
Rifleman1776 is offline  
Old July 22, 2011, 07:14 AM   #5
alloy
Senior Member
 
Join Date: September 11, 2008
Posts: 1,931
Didn't do any initial lube of the pad, but I use about 8-9 drops along the pad.
Generally there's enough in hand to size 3 or 4 cases for every one that I pick off the pad.
That's some good stuff that rcbs, a bottle lasts a long time, washes off with no soap, haven't stuck a case yet etc. First kind I tried and probobly the last.
__________________
Quote:
The uncomfortable question common to all who have had revolutionary changes imposed on them: are we now to accept what was done to us just because it was done?
Angelo Codevilla
alloy is offline  
Old July 22, 2011, 11:55 AM   #6
Jim243
Senior Member
 
Join Date: January 5, 2009
Posts: 4,335
Small misting bottle, a small amount of Lee Resizing Lube, couple oz of rubbing alcohol. Liberally spray, wait 10 min, alcohol will evaporate and leave a nice even film of lube on the cases, then resize. I do 50 at a time.

Jim
__________________
Si vis pacem, para bellum

Last edited by Jim243; July 22, 2011 at 12:02 PM.
Jim243 is offline  
Old July 22, 2011, 12:20 PM   #7
AllenJ
Senior Member
 
Join Date: December 11, 2009
Location: Northern California
Posts: 1,241
I run a small bead of lube the length of the case onto the lube pad, then work it in with my finger for a few seconds rubbing the same direction as I'm going to roll the cases. The first few cases I lube I'll roll one at a time, very lightly over the pad. As the lube gets used up I'll roll up to 5 at a time back and forth across the lubed area. So far this has worked perfectly for me.
AllenJ is offline  
Old July 22, 2011, 12:43 PM   #8
farmerboy
Junior member
 
Join Date: May 16, 2009
Location: Central Texas
Posts: 1,343
i use prob 1/2 tsp maybe (about 10 or so drops) roll on pad with finger tip. let soak in for about 1 min. and youre good to go. Love rcbs lube pad and a bottle will last for years for average reloader. Once you get your own system down you will love it.
farmerboy is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 04:07 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.08256 seconds with 9 queries