The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > The Smithy

Reply
 
Thread Tools
Old July 8, 2011, 09:26 PM   #1
BBroadside
Member
 
Join Date: June 6, 2010
Posts: 86
Paint for fixed revolver sights

I am finding it pretty hard to see my plain, silver-colored revolver sights in low light. Using a flashlight sometimes makes it better, sometimes worse. The tritium sights solution won't work for me, since both my Smiths have their sights integral to the rest of the weapon (my next S&W will have tritium but that is a ways in the future).

Do people prefer different colors for front and rear, or the same?

Orange? Red? Any principles to help choose, or just personal preference? Someone online said red on one front or rear and white on the other was a good idea; sounded plausible to me.

Is there any disadvantage to glow paint? If it can be any color, seems it shouldn't be worse than ordinary paint. Do any quick-access handgun safes have a lightbulb in them for heating? (I could have gone with that option for my tall safe, but went with a rod instead.) A little heating lightbulb may or may not be good enough to charge the paint, so I figured it may be worth a try.

(My overengineered, fanciful preference would be to put a little strobe light in the safe that would go on once, for an instant, just before the door was opened.)
BBroadside is offline  
Old July 8, 2011, 09:41 PM   #2
Jim Watson
Senior Member
 
Join Date: October 25, 2001
Location: Alabama
Posts: 11,025
I have Model Master Fluorescent Red (has an orange cast to the red) on several front sights. Applied over a white base coat it shows very well. I have not worked with luminescent paint. Black is ok with me for the rear, but if you want to try green or white, it is cheap and reversable.
Jim Watson is offline  
Old July 8, 2011, 09:49 PM   #3
Pbearperry
Senior Member
 
Join Date: December 9, 2008
Location: Massachusetts
Posts: 283
Most of my handguns have florescent green nail polish on the front sight.It's cheap and works like a charm.
Pbearperry is offline  
Old July 9, 2011, 08:36 AM   #4
Doyle
Senior Member
 
Join Date: June 20, 2007
Location: Starkville, MS (new to MS)
Posts: 4,726
I tried orange but found that bright white showed better contrast in low light. I use ordinary Testers model airplane paint. If you ever want to change, it will wipe off with acetone.
Doyle is offline  
Old July 9, 2011, 09:19 AM   #5
Crosshair
Senior Member
 
Join Date: December 16, 2004
Location: Grand Forks, ND
Posts: 5,320
I use nail polish as well. Cheap, durable, and easy to change if you want.
__________________
I don't carry a gun to go looking for trouble, I carry a gun in case trouble finds me.
Crosshair is offline  
Old July 9, 2011, 09:33 AM   #6
FAS1
Senior Member
 
Join Date: December 9, 2010
Location: San Antonio, TX
Posts: 262
Quote:
Do any quick-access handgun safes have a lightbulb in them for heating?
Not that I am aware of. Probably wouldn't be that hard to wire something up with a timer and a small low wattage bulb. Have it come on for a few hours at night to recharge your paint. I have no experience with that paint, how long it glows for or takes to recharge.
__________________
Glenn

FAS1 SAFE, LLC
FAS1 is offline  
Old July 9, 2011, 12:00 PM   #7
Rifleman1776
Senior Member
 
Join Date: April 25, 2010
Location: Arkansas
Posts: 3,309
One feature of the Ruger Redhawk I love is the interchangability for front sights.
But, for more versatility, I have painted the black sight using flourscent paints from the model shops. (cars, airplanes, etc.) Small bottles are not expensive, effective and last.
But, in low light, the nylon in yellow on the R'hawk works very well for me. I like it.
Some will argue, but a very good second choice is black. In low light it will still contrast with backgrounds and animals like deer.

Edit: I partially agree with Drail. I paint only the rear of the sight with flourscent paints. But, the all yellow nylon sight from Ruger doesn flare and is fine in bright sunlight.

Last edited by Rifleman1776; July 9, 2011 at 03:24 PM.
Rifleman1776 is offline  
Old July 9, 2011, 01:30 PM   #8
drail
Junior member
 
Join Date: February 2, 2008
Posts: 3,150
For non removable sights I carefully mask around the sight with tape and spray with flat black enamel. On the front sight I apply a small drop of yellow enamel for ease of sighting in low light. Painting the entire front sight with flourescent paint will throw you off in bright sunlight if the sun is to your left or right. The glare makes it difficult to center the front blade in the notch. On ranges with light colored targets in sunlight a solid flat black sight works the best. Occasionally you will encounter targets in the shade or with a drak background behind them. The little yellow dot allows you to find the front sight and get it on the target.
drail is offline  
Old May 5, 2014, 02:14 AM   #9
mojorisen279
Junior Member
 
Join Date: January 3, 2014
Posts: 2
Here's an idea for the paint...

http://www.sharpie.com/enUS/Pages/specialtyproduct.aspx
__________________
Using Tapatalk
mojorisen279 is offline  
Old May 5, 2014, 07:53 AM   #10
4V50 Gary
Staff
 
Join Date: November 2, 1998
Location: Colorado
Posts: 16,777
The advantage of paint is that it is not permanent and the front sight blade may be easily restored. Future generations of collectors will appreciate that.

The advantage of an insert is that it is more durable. Of course, this entails cutting a dovetail into the front sight and sticking in a piece of plastic. The front sight is forever altered and it costs more to do.
__________________
Vigilantibus et non dormientibus jura subveniunt. Molon Labe!
4V50 Gary is offline  
Old May 5, 2014, 09:34 AM   #11
PetahW
Senior Member
 
Join Date: September 19, 2008
Posts: 4,679
.

I had the same sighting problem with a couple of stainless steel revolvers - when sighted, the sights blended in with the top of the barrel/frame, and virtually disappeared.

I bought a BRIGHT SIGHTS kit, and have been completely satified.

http://brightsights.com/

One caveat: Don't simply apply the color of choice to the gunsights - the cleaned/degreased gunmetal (laq thinner) should first be coated with the white (colored) coating, and allowed to dry overnite before applying the color of choice (and the color coats likewise dried).

If the gunmetal's not done in the white before the color coat, I can guarantee you'll be disappointed with the result.

BTW - The white coating is excellent for making a white-outline rear sight notch (with a very fine, few hairs, artist's brush).


.
PetahW is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 08:57 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.08746 seconds with 9 queries