The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > Handloading, Reloading, and Bullet Casting

Reply
 
Thread Tools
Old April 3, 2011, 06:23 PM   #1
ltc444
Senior Member
 
Join Date: March 3, 2011
Location: Vernon AZ
Posts: 1,195
PMC Bronze 223

Is 223 PMC Bronze ammo reloadable?
ltc444 is offline  
Old April 3, 2011, 07:46 PM   #2
chasep255
Senior Member
 
Join Date: December 21, 2009
Location: NJ :(
Posts: 688
I actually just reloaded some the other day. Shot fine. If it's brass it should be reloadable. Of course always inspect your cases for damage.
__________________
I have mostly non-sporting firearms
In NJ, technically speaking, ALL guns are illegal
Also in my state there is such thing as a Class III BB gun :barf:
Happy to say that despite the NJ AWB I still manage to make my guns look scary
chasep255 is offline  
Old April 3, 2011, 07:54 PM   #3
Bamashooter
Senior Member
 
Join Date: March 12, 2010
Posts: 1,711
Yes. I have loaded hundreds without issue.
Bamashooter is offline  
Old April 3, 2011, 08:55 PM   #4
ltc444
Senior Member
 
Join Date: March 3, 2011
Location: Vernon AZ
Posts: 1,195
thanks for the info. It is brass. This is the first time I have seen PMC in brass. They threw in a case at cost when I bought my AR-15. Wanted to know if I should save the brass.
ltc444 is offline  
Old April 3, 2011, 09:31 PM   #5
m&p45acp10+1
Senior Member
 
Join Date: May 3, 2009
Location: Central Texas
Posts: 3,310
If it is being fired from a bolt action it has good case life. I have 40 pieces from 2 boxes of ammo that were thrown in with my Savage I have over 15 reloads out of them neck sizing them with a Lee Collet die. I trimmed them once. They are in my range bag loaded with 68 grain Hornady BTHP match at this time.

Note I pick up a lot of the PMC cases. A few have had primer pocket cripmps, but most do not. I throw the crimped primer pockets into a bag when I have enough ot justify it, and I run low on brass I will get a reamer for the primer pockets.
__________________
No matter how many times you do it and nothing happens it only takes something going wrong one time to kill you.
m&p45acp10+1 is offline  
Old April 5, 2011, 03:18 PM   #6
A_Gamehog
Senior Member
 
Join Date: February 9, 2009
Location: Central Oregun
Posts: 559
Similar in Capacity to Remington, the old PMC was really good stuff.
Old Brass for PMC had the (PMC) close together, New is spaced out (P M C )
The old stuff was made in Keno , Oregon?

.223 Rem Case Weight vs. Capacity

Case Manufacturer Case Weight* H20 Capacity**

Lake City 06 92.0 30.6
WCC99 95.5 30.5
Sellier & Belloit 92.3 30.5
Remington 92.3 30.4
PMC 93.5 30.4

Hirtenberger 93.7 30.4
Lake City 04 93.0 30.4
Federal 96.3 30.2
Hornady 93.9 30.1
IMG (Guatemalan) 95.4 30.1
Lapua (new lot) 93.4 30.1
Winchester 93.9 30.1
Olympic 97.4 30.0
Radway Arsenal 96.1 30.0
PMP 104.5 29.9
FNM 93-1 97.3 29.8
Lapua (old lot) 104.0 28.0



.223 AI Case Capacities
Lapua (old lot) 103.4 30.9
Winchester 95.5 32.2
Lapua (new lot) 93.4 32.4
Lake City 02 93.0 32.5
__________________
"Happiness is knowing the Barred Owl is Eating the Spotted Owl and environmentalists are watching Nature take it's course"
A_Gamehog is offline  
Old April 5, 2011, 03:48 PM   #7
PA-Joe
Senior Member
 
Join Date: June 9, 2010
Location: NEPA
Posts: 745
Check to see if it has a miliatary crimped primer.
PA-Joe is offline  
Old April 7, 2011, 06:36 PM   #8
cornbush
Senior Member
 
Join Date: September 29, 2008
Location: The retarded place below Idaho
Posts: 1,390
Look at them good, I have broken a couple decapping pins because the flash holes are not always centered on PMC brass.
__________________
The best shot I ever made was an accident
cornbush is offline  
Old April 7, 2011, 09:46 PM   #9
chiefr
Senior Member
 
Join Date: January 27, 2010
Location: AR
Posts: 1,296
PMC Ammo is made in Korea. IMHO, PMC is better than some of the stuff I have seen made here. The Mil ammo may or may not have crimped in primers, be sure to check. I get exceptional case life out of PMC brass.
chiefr is offline  
Old April 8, 2011, 08:53 AM   #10
dahermit
Senior Member
 
Join Date: October 28, 2006
Location: South Central Michigan...near Ohio, Indiana.
Posts: 3,542
Quote:
Is 223 PMC Bronze ammo reloadable?
Bronze is not Brass.
I am not aware of any company that uses Bronze as a cartridge case material.

FYI, Bronze is an alloy of Copper and Tin. Brass is an alloy of Copper and Zinc.
dahermit is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 08:56 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.07227 seconds with 9 queries